netcdf sgp10rlprofbe1newsC1.c1.20150921.000500 {
dimensions:
	time = UNLIMITED ; // (144 currently)
	height = 198 ;
variables:
	int base_time ;
		base_time:string = "21-Sep-15,00:05:00 GMT" ;
		base_time:long_name = "Base time in Epoch" ;
		base_time:units = "seconds since 1970-1-1 0:00:00 0:00" ;
	double time_offset(time) ;
		time_offset:long_name = "Time offset from base_time" ;
		time_offset:units = "seconds since 2015-9-21 00:05:00 0:00" ;
	double time(time) ;
		time:long_name = "Time offset from midnight" ;
		time:units = "seconds since 2015-9-21 00:00:00 0:00" ;
	float height(height) ;
		height:long_name = "Height above ground level" ;
		height:units = "km" ;
		height:comment = "Heights correspond to the middle of the bin" ;
	float asr(time, height) ;
		asr:long_name = "Aerosol scattering ratio" ;
		asr:units = "unitless" ;
		asr:missing_value = -9999.f ;
	int qc_asr(time, height) ;
		qc_asr:long_name = "Quality check results on field: Aerosol scattering ratio" ;
		qc_asr:units = "unitless" ;
		qc_asr:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_asr:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_asr:bit_1_assessment = "Bad" ;
		qc_asr:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_asr:bit_2_assessment = "Bad" ;
		qc_asr:bit_3_description = "Data quality suspect" ;
		qc_asr:bit_3_assessment = "Bad" ;
		qc_asr:bit_4_description = "Cloud contaminated" ;
		qc_asr:bit_4_assessment = "Bad" ;
		qc_asr:bit_5_description = "Error exceeds 25%" ;
		qc_asr:bit_5_assessment = "Bad" ;
	float asr_err(time, height) ;
		asr_err:long_name = "Aerosol scattering ratio uncertainty" ;
		asr_err:units = "unitless" ;
		asr_err:missing_value = -9999.f ;
	float bscat(time, height) ;
		bscat:long_name = "Aerosol backscatter coefficient" ;
		bscat:units = "1/(ster km)" ;
		bscat:missing_value = -9999.f ;
	int qc_bscat(time, height) ;
		qc_bscat:long_name = "Quality check results on field: Aerosol backscatter coefficient" ;
		qc_bscat:units = "unitless" ;
		qc_bscat:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_bscat:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_bscat:bit_1_assessment = "Bad" ;
		qc_bscat:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_bscat:bit_2_assessment = "Bad" ;
		qc_bscat:bit_3_description = "Data quality suspect" ;
		qc_bscat:bit_3_assessment = "Bad" ;
		qc_bscat:bit_4_description = "Cloud contaminated" ;
		qc_bscat:bit_4_assessment = "Bad" ;
		qc_bscat:bit_5_description = "Error exceeds 25%" ;
		qc_bscat:bit_5_assessment = "Bad" ;
	float bscat_err(time, height) ;
		bscat_err:long_name = "Aerosol backscatter coefficient uncertainty" ;
		bscat_err:units = "1/(ster km)" ;
		bscat_err:missing_value = -9999.f ;
	float ext(time, height) ;
		ext:long_name = "Aerosol extinction coefficient" ;
		ext:units = "km^(-1)" ;
		ext:missing_value = -9999.f ;
	int qc_ext(time, height) ;
		qc_ext:long_name = "Quality check results on field: Aerosol extinction coefficient" ;
		qc_ext:units = "unitless" ;
		qc_ext:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_ext:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_ext:bit_1_assessment = "Bad" ;
		qc_ext:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_ext:bit_2_assessment = "Bad" ;
		qc_ext:bit_3_description = "Data quality suspect" ;
		qc_ext:bit_3_assessment = "Bad" ;
		qc_ext:bit_4_description = "Cloud contaminated" ;
		qc_ext:bit_4_assessment = "Bad" ;
		qc_ext:bit_5_description = "Error exceeds 25%" ;
		qc_ext:bit_5_assessment = "Bad" ;
	float ext_err(time, height) ;
		ext_err:long_name = "Aerosol extinction coefficient uncertainty" ;
		ext_err:units = "km^(-1)" ;
		ext_err:missing_value = -9999.f ;
	float aod(time) ;
		aod:long_name = "Aerosol optical depth" ;
		aod:units = "unitless" ;
		aod:missing_value = -9999.f ;
	int qc_aod(time) ;
		qc_aod:long_name = "Quality check results on field: Aerosol optical depth" ;
		qc_aod:units = "unitless" ;
		qc_aod:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_aod:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_aod:bit_1_assessment = "Bad" ;
		qc_aod:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_aod:bit_2_assessment = "Bad" ;
		qc_aod:bit_3_description = "Data quality suspect" ;
		qc_aod:bit_3_assessment = "Bad" ;
		qc_aod:bit_4_description = "Cloud contaminated" ;
		qc_aod:bit_4_assessment = "Bad" ;
		qc_aod:bit_5_description = "Error exceeds 25%" ;
		qc_aod:bit_5_assessment = "Bad" ;
	float aod_err(time) ;
		aod_err:long_name = "Aerosol optical depth uncertainty" ;
		aod_err:units = "unitless" ;
		aod_err:missing_value = -9999.f ;
	float aod_profile(time, height) ;
		aod_profile:long_name = "Aerosol optical depth profile" ;
		aod_profile:units = "unitless" ;
		aod_profile:missing_value = -9999.f ;
	int qc_aod_profile(time, height) ;
		qc_aod_profile:long_name = "Quality check results on field: Aerosol optical depth profile" ;
		qc_aod_profile:units = "unitless" ;
		qc_aod_profile:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_aod_profile:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_aod_profile:bit_1_assessment = "Bad" ;
		qc_aod_profile:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_aod_profile:bit_2_assessment = "Bad" ;
		qc_aod_profile:bit_3_description = "Data quality suspect" ;
		qc_aod_profile:bit_3_assessment = "Bad" ;
		qc_aod_profile:bit_4_description = "Cloud contaminated" ;
		qc_aod_profile:bit_4_assessment = "Bad" ;
		qc_aod_profile:bit_5_description = "Error exceeds 25%" ;
		qc_aod_profile:bit_5_assessment = "Bad" ;
	float aod_max_height(time) ;
		aod_max_height:long_name = "Maximum height for aod" ;
		aod_max_height:units = "km" ;
	float dep(time, height) ;
		dep:long_name = "Linear depolarization ratio profile" ;
		dep:units = "%" ;
		dep:missing_value = -9999.f ;
	int qc_dep(time, height) ;
		qc_dep:long_name = "Quality check results on field: Linear depolarization ratio profile" ;
		qc_dep:units = "unitless" ;
		qc_dep:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_dep:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_dep:bit_1_assessment = "Bad" ;
		qc_dep:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_dep:bit_2_assessment = "Bad" ;
		qc_dep:bit_3_description = "Data quality suspect" ;
		qc_dep:bit_3_assessment = "Bad" ;
		qc_dep:bit_4_description = "Cloud contaminated" ;
		qc_dep:bit_4_assessment = "Bad" ;
		qc_dep:bit_5_description = "Error exceeds 25%" ;
		qc_dep:bit_5_assessment = "Bad" ;
	float dep_err(time, height) ;
		dep_err:long_name = "Linear depolarization ratio uncertainty" ;
		dep_err:units = "%" ;
		dep_err:missing_value = -9999.f ;
	float cot(time) ;
		cot:long_name = "Cloud optical depth from elastic data" ;
		cot:units = "unitless" ;
		cot:missing_value = -9999.f ;
	int qc_cot(time) ;
		qc_cot:long_name = "Quality check results on field: Cloud optical depth from elastic data" ;
		qc_cot:units = "unitless" ;
		qc_cot:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_cot:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_cot:bit_1_assessment = "Bad" ;
		qc_cot:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_cot:bit_2_assessment = "Bad" ;
		qc_cot:bit_3_description = "Data quality suspect" ;
		qc_cot:bit_3_assessment = "Bad" ;
		qc_cot:bit_4_description = "Cloud contaminated" ;
		qc_cot:bit_4_assessment = "Bad" ;
		qc_cot:bit_5_description = "Error exceeds 25%" ;
		qc_cot:bit_5_assessment = "Bad" ;
	float cot_err(time) ;
		cot_err:long_name = "Uncertainty in cloud optical depth from elastic data" ;
		cot_err:units = "unitless" ;
		cot_err:missing_value = -9999.f ;
	float pwv_mwr(time) ;
		pwv_mwr:long_name = "Precipitable water vapor from microwave radiometer" ;
		pwv_mwr:units = "cm" ;
		pwv_mwr:valid_min = 0.f ;
		pwv_mwr:missing_value = -9999.f ;
	float pwv(time) ;
		pwv:long_name = "Precipitable water vapor observed by the Raman lidar" ;
		pwv:units = "cm" ;
		pwv:missing_value = -9999.f ;
		pwv:comment = "Since the lidar may not be able to sense the entire column, the integrated amount of water vapor from the lidar is scaled by the unitless estimate of the fraction of the water vapor in the column the lidar senses to provide the total PWV" ;
	int qc_pwv(time) ;
		qc_pwv:long_name = "Quality check results on field: Precipitable water vapor observed by the Raman lidar" ;
		qc_pwv:units = "unitless" ;
		qc_pwv:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_pwv:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_pwv:bit_1_assessment = "Bad" ;
		qc_pwv:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_pwv:bit_2_assessment = "Bad" ;
		qc_pwv:bit_3_description = "Data quality suspect" ;
		qc_pwv:bit_3_assessment = "Bad" ;
		qc_pwv:bit_4_description = "Cloud contaminated" ;
		qc_pwv:bit_4_assessment = "Bad" ;
		qc_pwv:bit_5_description = "Error exceeds 25%" ;
		qc_pwv:bit_5_assessment = "Bad" ;
	float pwv_err(time) ;
		pwv_err:long_name = "Uncertainty in precipitable water vapor observed by the Raman lidar" ;
		pwv_err:units = "cm" ;
		pwv_err:missing_value = -9999.f ;
	float pwv_fraction(time) ;
		pwv_fraction:long_name = "Fraction of the total column amount of water vapor the Raman lidar senses" ;
		pwv_fraction:units = "unitless" ;
		pwv_fraction:valid_min = 0.f ;
		pwv_fraction:missing_value = -9999.f ;
		pwv_fraction:comment = "Estimated from the water vapor profiles in sgpaeriprof3feltzC1.c1" ;
	float mr_max_height(time) ;
		mr_max_height:long_name = "Suggested maximum altitude to use the water vapor from the Raman lidar" ;
		mr_max_height:units = "km" ;
		mr_max_height:valid_min = 0.f ;
		mr_max_height:missing_value = -9999.f ;
		mr_max_height:comment = "This is the first altitude above 1 km where the random error is larger than 25%" ;
	float mr(time, height) ;
		mr:long_name = "Water vapor mixing ratio observed by the Raman lidar" ;
		mr:units = "g/km" ;
		mr:missing_value = -9999.f ;
	int qc_mr(time, height) ;
		qc_mr:long_name = "Quality check results on field: Water vapor mixing ratio observed by the Raman lidar" ;
		qc_mr:units = "unitless" ;
		qc_mr:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_mr:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_mr:bit_1_assessment = "Bad" ;
		qc_mr:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_mr:bit_2_assessment = "Bad" ;
		qc_mr:bit_3_description = "Data quality suspect" ;
		qc_mr:bit_3_assessment = "Bad" ;
		qc_mr:bit_4_description = "Cloud contaminated" ;
		qc_mr:bit_4_assessment = "Bad" ;
		qc_mr:bit_5_description = "Error exceeds 25%" ;
		qc_mr:bit_5_assessment = "Bad" ;
	float mr_err(time, height) ;
		mr_err:long_name = "Uncertainty in water vapor mixing ratio observed by the Raman lidar" ;
		mr_err:units = "g/km" ;
		mr_err:missing_value = -9999.f ;
	float rh(time, height) ;
		rh:long_name = "Relative humidity observed by the Raman lidar" ;
		rh:units = "%" ;
		rh:missing_value = -9999.f ;
	int qc_rh(time, height) ;
		qc_rh:long_name = "Quality check results on field: Relative humidity observed by the Raman lidar" ;
		qc_rh:units = "unitless" ;
		qc_rh:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_rh:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_rh:bit_1_assessment = "Bad" ;
		qc_rh:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_rh:bit_2_assessment = "Bad" ;
		qc_rh:bit_3_description = "Data quality suspect" ;
		qc_rh:bit_3_assessment = "Bad" ;
		qc_rh:bit_4_description = "Cloud contaminated" ;
		qc_rh:bit_4_assessment = "Bad" ;
		qc_rh:bit_5_description = "Error exceeds 25%" ;
		qc_rh:bit_5_assessment = "Bad" ;
	float temperature(time, height) ;
		temperature:long_name = "Temperature from sgpaeriprof3feltzC1.c1" ;
		temperature:units = "C" ;
		temperature:missing_value = -9999.f ;
		temperature:comment = "Data interpolated from sgpaeriprof3feltzC1.c1 to Raman lidar time/height grid" ;
	float pressure(time, height) ;
		pressure:long_name = "Pressure from sgpaeriprof3feltzC1.c1" ;
		pressure:units = "mb" ;
		pressure:missing_value = -9999.f ;
		pressure:comment = "Data interpolated from sgpaeriprof3feltzC1.c1 to Raman lidar time/height grid" ;
	float mr_sonde(time, height) ;
		mr_sonde:long_name = "Sonde mixing ratio" ;
		mr_sonde:units = "g/kg" ;
		mr_sonde:valid_min = 0.f ;
		mr_sonde:missing_value = -9999.f ;
	int sample_times_sonde(time) ;
		sample_times_sonde:long_name = "Sonde sample times" ;
		sample_times_sonde:units = "unitless" ;
		sample_times_sonde:comment = "Flag indicating whether or not there was a sample from the radiosonde during the lidars averaging interval (1) or not (0)" ;
	int cmask(time, height) ;
		cmask:long_name = "Cloud mask from depolarization VAP" ;
		cmask:units = "unitless" ;
		cmask:missing_value = -9999 ;
	int qc_cmask(time, height) ;
		qc_cmask:long_name = "Quality check results on field: Cloud mask from depolarization VAP" ;
		qc_cmask:units = "unitless" ;
		qc_cmask:description = "This field contains bit packed values which should be interpreted as listed. No bits set (zero) represents good data." ;
		qc_cmask:bit_1_description = "Data value not available in input file, data value set to -9999 in output file." ;
		qc_cmask:bit_1_assessment = "Bad" ;
		qc_cmask:bit_2_description = "Hatch closed, data value set to -9999 in output file." ;
		qc_cmask:bit_2_assessment = "Bad" ;
		qc_cmask:bit_3_description = "Data quality suspect" ;
		qc_cmask:bit_3_assessment = "Bad" ;
		qc_cmask:bit_4_description = "Cloud contaminated" ;
		qc_cmask:bit_4_assessment = "Bad" ;
		qc_cmask:bit_5_description = "Error exceeds 25%" ;
		qc_cmask:bit_5_assessment = "Bad" ;
	float lat ;
		lat:long_name = "North latitude" ;
		lat:units = "degree_N" ;
		lat:valid_min = -90.f ;
		lat:valid_max = 90.f ;
	float lon ;
		lon:long_name = "East longitude" ;
		lon:units = "degree_E" ;
		lon:valid_min = -180.f ;
		lon:valid_max = 180.f ;
	float alt ;
		alt:long_name = "Altitude above mean sea level" ;
		alt:units = "m" ;

// global attributes:
		:process_version = "$State: vap-rlprof_be-0.5-0.el6$" ;
		:command_line = "/apps/process/bin/rlprof_be10 -f C1 -s sgp -d 20150921" ;
		:site_id = "sgp" ;
		:facility_id = "C1" ;
		:dod_version = "0.1" ;
		:qc_standards_version = "1.0" ;
		:mr_version = "$State: vap-rlprof_mr-1.3-0.el6$" ;
		:asr_version = "$State: vap-rlprof_asr-3.13-0.el6$" ;
		:ext_version = "$State: vap-rlprof_ext-0.9-0.el6$" ;
		:dep_version = "$State: vap-rlprof_dep-2.1-0.el6$" ;
		:mr_command_line = "/apps/process/bin/rlprof_mr10 -s sgp -f C1 -A -d 20150920" ;
		:asr_command_line = "/apps/process/bin/rlprof_asr10 -s sgp -f C1 -d 20150920" ;
		:ext_command_line = "/apps/process/bin/rlprof_ext10 -s sgp -f C1 -d 20150920" ;
		:dep_command_line = "/apps/process/bin/rlprof_dep10 -s sgp -f C1 -d 20150920" ;
		:averaging_time = "10" ;
		:input_datastreams_description = "A string consisting of the datastream(s), datastream version(s), and datastream date (range)." ;
		:input_datastreams_num = 12 ;
		:input_datastreams = "sgp10rlprofasr1ferrC1.c0.20150920.000000.cdf : $State: vap-rlprof_asr-3.13-0.el6$ : 20150920.000000 - 20150922.000000,\n",
			"sgp10rlprofdep1turnC1.c0.20150920.000000.cdf : $State: vap-rlprof_dep-2.1-0.el6$ : 20150920.000000 - 20150922.000000,\n",
			"sgp10rlprofext1ferrC1.c0.20150920.000000.cdf : $State: vap-rlprof_ext-0.9-0.el6$ : 20150920.000000 - 20150922.000000,\n",
			"sgp10rlprofmr1turnC1.c0.20150920.000000.cdf : $State: vap-rlprof_mr-1.3-0.el6$ : 20150920.000000 - 20150922.000000," ;
		:mr_temperature_source = "sgpaeriprof3feltzC1.c1" ;
		:asr_temperature_source = "sgpaeriprof3feltzC1.c1" ;
		:ext_temperature_source = "sgpaeriprof3feltzC1.c1" ;
		:mr_calibration_comment = "Automatic calibration to MWR successful" ;
		:sonde_source = "sgplssondeC1.c1" ;
		:mr_aerosol_diff_trans_correction = "Differential transmission correction for aerosols NOT APPLIED" ;
		:asr_aerosol_diff_trans_correction = "Differential transmission correction for aerosols APPLIED" ;
		:history = "created by dsmgr on machine ruby on Wed Oct  7 17:01:38 2015" ;
}