DQR ID | Subject | Data Streams Affected | Data Quality Metric |
---|
D160830.2 | OLI/UHSAS/M1 - High counts below 100 nm | oliaosuhsasM1.a1 | Incorrect |
D160901.3 | OLI/CPC/M1 - Collection issue | oliaoscpcuM1.b1 | Missing |
D160923.2 | OLI/PSAP/M1 - Data gaps from pump turned off | oliaospsap3wM1.a1 | Incorrect |
D161011.4 | OLI/UHSAS/M1 - Instrument software stopped | oliaosuhsasM1.a1 | Missing |
D161024.3 | OLI/NEPHELOMETER/M1 - Dry Nephelometer bulb replaced | oliaosnephdryM1.b1 | Incorrect |
D161027.5 | OLI/CPC/M1 - Instrument connectivity issue | oliaoscpcuM1.b1 | Missing |
D161104.1 | OLI/CPC/M1 - Nozzle pressure elevated | oliaoscpcuM1.b1 | Does not affect quality |
D161211.1 | OLI/PSAP/M1 - Incorrect reset of transmittance after filter change | oliaospsap3wM1.a1 | Incorrect |
D161211.2 | OLI/PSAP/M1 - Data Gaps > 1h due to Tr<0.7, pump turned off, power failures | oliaospsap3wM1.a1 | Incorrect |
D161211.3 | OLI/PSAP/M1 - Data Gaps > 1h due to Tr<0.7, pump turned off, etc. | oliaospsap3wM1.a1 | Incorrect |
D161211.4 | OLI/PSAP/M1 - Data Gaps > 1h due to Tr<0.7, pump turned off | oliaospsap3wM1.a1 | Incorrect |
D161220.3 | OLI/CPC/M1 - Sampling cabin air | oliaoscpcuM1.b1 | Incorrect |
D170105.9 | OLI/CPC/M1 - Instruments powered down | oliaoscpcuM1.b1 | Missing |
D170110.2 | OLI/AOS/M1 - Severe storm | oliaosnephdryM1.b1, oliaospsap3wM1.a1, oliaoscpcuM1.b1, oliaosuhsasM1.a1 | Does not affect quality |
D170127.4 | OLI/CPC/M1 - Instrument Shut Down | oliaoscpcuM1.b1 | Missing |
D170127.7 | OLI/PSAP/M1 - Instrument pump off | oliaospsap3wM1.a1 | Incorrect |
D170203.6 | OLI/UHSAS/M1 - Inlet plumbing issues | oliaosuhsasM1.a1 | Incorrect |
D170203.8 | OLI/NEPHELOMETER/PSAP/IMPACTOR/M1 - Leak in the inlet lines | oliaosnephdryM1.b1, oliaospsap3wM1.a1 | Suspect |
D170208.2 | OLI/NEPHELOMETER/PSAP/IMPACTOR/M1 - Low impactor flow | oliaosnephdryM1.b1, oliaospsap3wM1.a1 | Suspect |
D170221.6 | OLI/AOS/M1 - Instrument Butanol Reservoir contaminated with water | oliaoscpcuM1.b1 | Incorrect |
D170320.6 | OLI/ALL/M1 - Power Outage | oliaospsap3wM1.a1, oliaosnephdryM1.b1, oliaoscpcuM1.b1, oliaosuhsasM1.a1 | Does not affect quality |
D170329.10 | OLI/AOS/M1 - Power outage | oliaosnephdryM1.b1 | Missing |
D170329.4 | OLI/AOS/M1 - Power outage | oliaoscpcuM1.b1 | Missing |
D170329.5 | OLI/AOS/M1 - Power outage and freezing conditions | oliaoscpcuM1.b1 | Missing |
D170329.6 | OLI/AOS/M1 - Power outage | oliaosuhsasM1.a1 | Missing |
D170406.2 | OLI/AOS/M1 - All serial instruments in the AOS down | oliaosnephdryM1.b1, oliaospsap3wM1.a1, oliaoscpcuM1.b1 | Missing |
D170419.2 | OLI/UHSAS/M1 - Contamination in the optics chamber | oliaosuhsasM1.a1 | Incorrect |
Subject: | OLI/PSAP/M1 - Data gaps from pump turned off |
DataStreams: | oliaospsap3wM1.a1
|
Description: | Data Gaps > 1h due to Tr<0.7, pump turned off, etc.
New Operator replaced previous Operator and new Operator unaware of need to change the
filter. |
Measurements: | oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - Absorption coefficient red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_10um_PSAP3W_1) - TrB
- psap_flags
- Absorption Coefficient Blue, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_B_Dry_10um_PSAP3W_1) - averaging_time
- transmittance_R
- TrG
- TrR
- Absorption coefficient green, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_G_Dry_1um_PSAP3W_1) - transmittance_G
- mass_flow
- dilution_flow
- dilution_flow_valve_position
- dilution_flow_setpoint
- Absorption Coefficient Red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Absorption coefficient blue, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_B_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W) - transmittance_B
- Absorption coefficient, green wavelength, 3 wavelength PSAP, low RH, 10 um size
cut(Ba_G_Dry_10um_PSAP3W_1) - mass_flow_voltage
|
Subject: | OLI/PSAP/M1 - Incorrect reset of transmittance after filter change |
DataStreams: | oliaospsap3wM1.a1
|
Description: | Operator MAY have changed filter but didn't reset transmission to 100%. Data invalid. |
Measurements: | oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - Absorption coefficient red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_10um_PSAP3W_1) - TrB
- psap_flags
- Absorption Coefficient Blue, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_B_Dry_10um_PSAP3W_1) - averaging_time
- transmittance_R
- TrG
- TrR
- Absorption coefficient green, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_G_Dry_1um_PSAP3W_1) - transmittance_G
- mass_flow
- dilution_flow
- dilution_flow_valve_position
- dilution_flow_setpoint
- Absorption Coefficient Red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Absorption coefficient blue, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_B_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W) - transmittance_B
- Absorption coefficient, green wavelength, 3 wavelength PSAP, low RH, 10 um size
cut(Ba_G_Dry_10um_PSAP3W_1) - mass_flow_voltage
|
Subject: | OLI/PSAP/M1 - Data Gaps > 1h due to Tr<0.7, pump turned off, power failures |
DataStreams: | oliaospsap3wM1.a1
|
Description: | The manufacturer specifies filter must be changed for transmission less than 0.7. This is
not always possible with Operator staffing.
This is different from D161211.1 where on that DQR, the filter was changed, but
transmittance not reset. |
Measurements: | oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - Absorption coefficient red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_10um_PSAP3W_1) - TrB
- psap_flags
- Absorption Coefficient Blue, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_B_Dry_10um_PSAP3W_1) - averaging_time
- transmittance_R
- TrG
- TrR
- Absorption coefficient green, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_G_Dry_1um_PSAP3W_1) - transmittance_G
- mass_flow
- dilution_flow
- dilution_flow_valve_position
- dilution_flow_setpoint
- Absorption Coefficient Red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Absorption coefficient blue, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_B_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W) - transmittance_B
- Absorption coefficient, green wavelength, 3 wavelength PSAP, low RH, 10 um size
cut(Ba_G_Dry_10um_PSAP3W_1) - mass_flow_voltage
|
Subject: | OLI/PSAP/M1 - Data Gaps > 1h due to Tr<0.7, pump turned off, etc. |
DataStreams: | oliaospsap3wM1.a1
|
Description: | Manufacturer specifies transmission greater than 0.7 for valid data. This isn't always
possible with Operator staffing. |
Measurements: | oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - Absorption coefficient red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_10um_PSAP3W_1) - TrB
- psap_flags
- Absorption Coefficient Blue, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_B_Dry_10um_PSAP3W_1) - averaging_time
- transmittance_R
- TrG
- TrR
- Absorption coefficient green, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_G_Dry_1um_PSAP3W_1) - transmittance_G
- mass_flow
- dilution_flow
- dilution_flow_valve_position
- dilution_flow_setpoint
- Absorption Coefficient Red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Absorption coefficient blue, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_B_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W) - transmittance_B
- Absorption coefficient, green wavelength, 3 wavelength PSAP, low RH, 10 um size
cut(Ba_G_Dry_10um_PSAP3W_1) - mass_flow_voltage
|
Subject: | OLI/PSAP/M1 - Data Gaps > 1h due to Tr<0.7, pump turned off |
DataStreams: | oliaospsap3wM1.a1
|
Description: | Vendor specifies transmission greater than 0.7 for valid data. This isn't possible with
Operating staffing. |
Measurements: | oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - Absorption coefficient red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_10um_PSAP3W_1) - TrB
- psap_flags
- Absorption Coefficient Blue, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_B_Dry_10um_PSAP3W_1) - averaging_time
- transmittance_R
- TrG
- TrR
- Absorption coefficient green, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_G_Dry_1um_PSAP3W_1) - transmittance_G
- mass_flow
- dilution_flow
- dilution_flow_valve_position
- dilution_flow_setpoint
- Absorption Coefficient Red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Absorption coefficient blue, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_B_Dry_1um_PSAP3W_1) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W) - transmittance_B
- Absorption coefficient, green wavelength, 3 wavelength PSAP, low RH, 10 um size
cut(Ba_G_Dry_10um_PSAP3W_1) - mass_flow_voltage
|
Subject: | OLI/AOS/M1 - Severe storm |
DataStreams: | oliaosnephdryM1.b1, oliaospsap3wM1.a1, oliaoscpcuM1.b1, oliaosuhsasM1.a1
|
Description: | The site lost power during a severe winter storm. Operators on site were not able to get
out and restart the generators to bring AOS instrument systems back up until 1/9/2017. |
Measurements: | oliaosuhsasM1.a1: - base_time
- Temperature at the ground station(temperature)
- North latitude(lat)
- sheath_flow
- East longitude(lon)
- current
- sample_pressure
- Altitude above mean sea level(alt)
- differential_voltage
- time
- Particle size distribution, limited by lower_size_limit and upper_size_limit(size_distribution)
- reference
- time_offset
- bin_num
- purge_flow
- scattering_voltage
- lower_size_limit
- upper_size_limit
- flow
- unit_temperature
- sampling_volume
- auxiliary
oliaosnephdryM1.b1: - base_time
- instrument_state
- Altitude above mean sea level(alt)
- lamp_voltage
- North latitude(lat)
- Aerosol total light scattering coefficient, nominal blue wavelength at dry or
reference RH(Bs_B_Dry_Neph3W) - qc_Bbs_R_Dry_Neph3W
- qc_Bs_R_Dry_Neph3W
- time
- qc_Bs_B_Dry_Neph3W
- qc_T_Neph_Inlet_Dry
- qc_Bbs_B_Dry_Neph3W
- qc_Bs_G_Dry_Neph3W
- East longitude(lon)
- Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
dry or reference RH(Bbs_R_Dry_Neph3W) - Aerosol total light scattering coefficient, nominal red wavelength at dry or
reference RH(Bs_R_Dry_Neph3W) - qc_impactor_state
- Aerosol total light scattering coefficient, nominal green wavelength at dry or
reference RH(Bs_G_Dry_Neph3W) - qc_T_Neph_Dry
- qc_RH_Neph_Dry
- Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
at dry or reference RH(Bbs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
at dry or reference RH(Bbs_G_Dry_Neph3W) - RH_Neph_Dry
- T_Neph_Inlet_Dry
- qc_Bbs_G_Dry_Neph3W
- P_Neph_Dry
- time_offset
- Impactor particle size cut(impactor_state)
- qc_P_Neph_Dry
- lamp_current
- T_Neph_Dry
- seconds_after_transition
- density_correction_factor
- mode_flag
oliaoscpcuM1.b1: - saturation_temp
- aerosol_flow
- ambient_pressure
- base_time
- time_offset
- fraction_full
- optics_temp
- condensation_temp
- North latitude(lat)
- cabinet_temp
- nozzle_pressure
- Aerosol concentration averaged over times to match N_CCN(concentration)
- qc_concentration
- Altitude above mean sea level(alt)
- East longitude(lon)
- time
- orifice_pressure
- liquid_level
- laser_current
oliaospsap3wM1.a1: - Absorption coefficient green, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_G_Dry_1um_PSAP3W_1) - North latitude(lat)
- TrR
- East longitude(lon)
- Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - time
- TrB
- transmittance_R
- TrG
- transmittance_G
- transmittance_B
- time_offset
- Altitude above mean sea level(alt)
- dilution_flow
- Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - base_time
- Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W) - Absorption coefficient, green wavelength, 3 wavelength PSAP, low RH, 10 um size
cut(Ba_G_Dry_10um_PSAP3W_1) - Absorption coefficient red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_10um_PSAP3W_1) - psap_flags
- dilution_flow_valve_position
- mass_flow
- mass_flow_voltage
- Absorption Coefficient Blue, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_B_Dry_10um_PSAP3W_1) - Absorption coefficient blue, corrected for flow and sample area, 3 wavelength
PSAP, 1 um size cut(Ba_B_Dry_1um_PSAP3W_1) - averaging_time
- dilution_flow_setpoint
- Absorption Coefficient Red, corrected for flow and sample area, 3 wavelength
PSAP, 10 um size cut(Ba_R_Dry_1um_PSAP3W_1)
|
Subject: | OLI/NEPHELOMETER/PSAP/IMPACTOR/M1 - Leak in the inlet lines |
DataStreams: | oliaosnephdryM1.b1, oliaospsap3wM1.a1
|
Description: | Leak in the inlet lines after the impactor. Impactor flow below nominal. Data quality
suspect. |
Measurements: | oliaosnephdryM1.b1: - instrument_state
- Aerosol total light scattering coefficient, nominal green wavelength at dry or
reference RH(Bs_G_Dry_Neph3W) - Impactor particle size cut(impactor_state)
- lamp_voltage
- lamp_current
- T_Neph_Dry
- Aerosol total light scattering coefficient, nominal blue wavelength at dry or
reference RH(Bs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
at dry or reference RH(Bbs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
dry or reference RH(Bbs_R_Dry_Neph3W) - seconds_after_transition
- Aerosol total light scattering coefficient, nominal red wavelength at dry or
reference RH(Bs_R_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
at dry or reference RH(Bbs_G_Dry_Neph3W) - density_correction_factor
- RH_Neph_Dry
- T_Neph_Inlet_Dry
- P_Neph_Dry
- mode_flag
oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - transmittance_R
- transmittance_G
- dilution_flow_valve_position
- transmittance_B
- mass_flow
- dilution_flow
- dilution_flow_setpoint
- Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W)
|
Subject: | OLI/NEPHELOMETER/PSAP/IMPACTOR/M1 - Low impactor flow |
DataStreams: | oliaosnephdryM1.b1, oliaospsap3wM1.a1
|
Description: | Low flow through the imapctor after recovering from power loss. Data quality suspect. |
Measurements: | oliaosnephdryM1.b1: - instrument_state
- Aerosol total light scattering coefficient, nominal green wavelength at dry or
reference RH(Bs_G_Dry_Neph3W) - Impactor particle size cut(impactor_state)
- lamp_voltage
- lamp_current
- T_Neph_Dry
- Aerosol total light scattering coefficient, nominal blue wavelength at dry or
reference RH(Bs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
at dry or reference RH(Bbs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
dry or reference RH(Bbs_R_Dry_Neph3W) - seconds_after_transition
- Aerosol total light scattering coefficient, nominal red wavelength at dry or
reference RH(Bs_R_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
at dry or reference RH(Bbs_G_Dry_Neph3W) - density_correction_factor
- RH_Neph_Dry
- T_Neph_Inlet_Dry
- P_Neph_Dry
- mode_flag
oliaospsap3wM1.a1: - Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - transmittance_R
- transmittance_G
- dilution_flow_valve_position
- transmittance_B
- mass_flow
- dilution_flow
- dilution_flow_setpoint
- Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W)
|
Subject: | OLI/ALL/M1 - Power Outage |
DataStreams: | oliaospsap3wM1.a1, oliaosnephdryM1.b1, oliaoscpcuM1.b1, oliaosuhsasM1.a1
|
Description: | OLI suffered from a prolonged power outage. The instruments were brought back up over the
course of 3/9 so the end date will be different for each instrument. Any problems with
the instruments after being brought back online will be covered by separate DQRs. |
Measurements: | oliaosuhsasM1.a1: - base_time
- Temperature at the ground station(temperature)
- time_offset
- North latitude(lat)
- bin_num
- sheath_flow
- East longitude(lon)
- purge_flow
- scattering_voltage
- lower_size_limit
- upper_size_limit
- current
- sample_pressure
- Altitude above mean sea level(alt)
- differential_voltage
- time
- flow
- sampling_volume
- unit_temperature
- Particle size distribution, limited by lower_size_limit and upper_size_limit(size_distribution)
- auxiliary
- reference
oliaosnephdryM1.b1: - base_time
- instrument_state
- Altitude above mean sea level(alt)
- Aerosol total light scattering coefficient, nominal green wavelength at dry or
reference RH(Bs_G_Dry_Neph3W) - qc_T_Neph_Dry
- North latitude(lat)
- lamp_voltage
- qc_RH_Neph_Dry
- Aerosol total light scattering coefficient, nominal blue wavelength at dry or
reference RH(Bs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
at dry or reference RH(Bbs_B_Dry_Neph3W) - qc_Bbs_R_Dry_Neph3W
- qc_Bs_R_Dry_Neph3W
- Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
at dry or reference RH(Bbs_G_Dry_Neph3W) - RH_Neph_Dry
- T_Neph_Inlet_Dry
- time
- qc_Bbs_G_Dry_Neph3W
- P_Neph_Dry
- qc_Bs_B_Dry_Neph3W
- qc_T_Neph_Inlet_Dry
- qc_Bbs_B_Dry_Neph3W
- time_offset
- Impactor particle size cut(impactor_state)
- qc_P_Neph_Dry
- lamp_current
- T_Neph_Dry
- qc_Bs_G_Dry_Neph3W
- East longitude(lon)
- Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
dry or reference RH(Bbs_R_Dry_Neph3W) - seconds_after_transition
- Aerosol total light scattering coefficient, nominal red wavelength at dry or
reference RH(Bs_R_Dry_Neph3W) - density_correction_factor
- mode_flag
- qc_impactor_state
oliaoscpcuM1.b1: - North latitude(lat)
- saturation_temp
- cabinet_temp
- nozzle_pressure
- aerosol_flow
- Aerosol concentration averaged over times to match N_CCN(concentration)
- ambient_pressure
- base_time
- qc_concentration
- time_offset
- fraction_full
- Altitude above mean sea level(alt)
- optics_temp
- East longitude(lon)
- condensation_temp
- time
- orifice_pressure
- liquid_level
- laser_current
oliaospsap3wM1.a1: - dilution_flow_valve_position
- North latitude(lat)
- mass_flow
- East longitude(lon)
- time
- Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - transmittance_R
- transmittance_G
- transmittance_B
- time_offset
- Altitude above mean sea level(alt)
- dilution_flow
- dilution_flow_setpoint
- Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - base_time
- Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W)
|
Subject: | OLI/AOS/M1 - All serial instruments in the AOS down |
DataStreams: | oliaosnephdryM1.b1, oliaospsap3wM1.a1, oliaoscpcuM1.b1
|
Description: | The Moxa IP to serial server failed. There is no communication to any of the serial
instruments in the AOS, so the data is missing. Initially, it was able to be rebooted and
then worked for a while, but after a day it no longer started up. |
Measurements: | oliaosnephdryM1.b1: - instrument_state
- base_time
- Altitude above mean sea level(alt)
- Aerosol total light scattering coefficient, nominal green wavelength at dry or
reference RH(Bs_G_Dry_Neph3W) - qc_T_Neph_Dry
- North latitude(lat)
- lamp_voltage
- qc_RH_Neph_Dry
- Aerosol total light scattering coefficient, nominal blue wavelength at dry or
reference RH(Bs_B_Dry_Neph3W) - Aerosol back-hemispheric light scattering coefficient, nominal blue wavelength
at dry or reference RH(Bbs_B_Dry_Neph3W) - qc_Bbs_R_Dry_Neph3W
- qc_Bs_R_Dry_Neph3W
- Aerosol back-hemispheric light scattering coefficient, nominal green wavelength
at dry or reference RH(Bbs_G_Dry_Neph3W) - RH_Neph_Dry
- T_Neph_Inlet_Dry
- time
- qc_Bbs_G_Dry_Neph3W
- P_Neph_Dry
- qc_Bs_B_Dry_Neph3W
- qc_T_Neph_Inlet_Dry
- qc_Bbs_B_Dry_Neph3W
- time_offset
- Impactor particle size cut(impactor_state)
- qc_P_Neph_Dry
- T_Neph_Dry
- lamp_current
- qc_Bs_G_Dry_Neph3W
- East longitude(lon)
- Aerosol back-hemispheric light scattering coefficient, nominal red wavelength at
dry or reference RH(Bbs_R_Dry_Neph3W) - seconds_after_transition
- Aerosol total light scattering coefficient, nominal red wavelength at dry or
reference RH(Bs_R_Dry_Neph3W) - density_correction_factor
- mode_flag
- qc_impactor_state
oliaoscpcuM1.b1: - North latitude(lat)
- saturation_temp
- cabinet_temp
- nozzle_pressure
- aerosol_flow
- Aerosol concentration averaged over times to match N_CCN(concentration)
- ambient_pressure
- base_time
- qc_concentration
- time_offset
- fraction_full
- Altitude above mean sea level(alt)
- optics_temp
- East longitude(lon)
- condensation_temp
- time
- orifice_pressure
- liquid_level
- laser_current
oliaospsap3wM1.a1: - dilution_flow_valve_position
- North latitude(lat)
- mass_flow
- East longitude(lon)
- Aerosol light absorption coefficient, nominal red wavelength at dry or reference
RH(Ba_R_PSAP3W) - time
- transmittance_R
- transmittance_G
- transmittance_B
- time_offset
- Altitude above mean sea level(alt)
- dilution_flow
- dilution_flow_setpoint
- Aerosol light absorption coefficient, nominal green wavelength at dry or
reference RH(Ba_G_PSAP3W) - base_time
- Aerosol light absorption coefficient, nominal blue wavelength at dry or
reference RH(Ba_B_PSAP3W)
|