DQR ID | Subject | Data Streams Affected |
---|
D000127.1 | TWP/MWR/C2 - Uncertainty in clock time | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D000609.1 | TWP/MWR/C2 - Installation | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D010227.4 | TWP/MWR/C2 - Excessive wet_window flags | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D040211.4 | TWP/MWR/C2 - thermal instability | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D040920.1 | TWP/MWR/C2 - Data collection problem | twpmwrC2.00, twpmwrlosC2.b1, twpmwrtipC2.a1 |
D050310.3 | TWP/MWR/C2 - Heater problem | twp5mwravgC2.c1, twpmwrlosC2.b1, twpmwrtipC2.a1 |
D050524.2 | TWP/MWR/C2 - mixer temperature | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D050725.10 | TWP/MWR/C2 - Reprocessed: Revised Retrieval Coefficients | twp5mwravgC2.c1, twpmwrlosC2.b1, twpqmemwrcolC2.c1 |
D050928.2 | TWP/MWR/C2 - New software version (4.15) installed | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D060420.10 | TWP/MWR/C2 - software upgrade (version 3.29) | twpmwrlosC2.b1 |
D061002.1 | TWP/MWR/C2 - Missing data | twp5mwravgC2.c1, twpmwrC2.00, twpmwrlosC2.b1, twpmwrtipC2.a1 |
D061121.1 | TWP/MWR/C2 - Missing Data | twpmwrlosC2.b1 |
D061213.3 | TWP/MWR/C2 - Reprocessed: New Calibration coefficients | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D070412.3 | TWP/MWR/C1/C2 - Sun in the field of view | twpmwrlosC1.b1, twpmwrlosC2.b1, twpmwrtipC1.a1, twpmwrtipC2.a1 |
D081216.1 | TWP/MWR/C2 - Incorrect ambient temperature during rain | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D090417.3 | TWP/MWR/C2 - Intermittent data | twpmwrlosC2.b1, twpmwrtipC2.a1 |
D990107.1 | TWP/MWR/C2 - Software Change | twpmwrlosC2.b1 |
Subject: | TWP/MWR/C2 - Uncertainty in clock time |
DataStreams: | twpmwrlosC2.b1, twpmwrtipC2.a1
|
Description: | At ARCS2, the MWR computer clock was not being updated because no NTP time service
software was installed on the computer. During Nauru99, on 6/24/99, the clock was found to be 3
minutes and 17 seconds fast.
Assuming that the time was properly set at installation on 10/26/98 (which is not
indicated in the installation report) and never reset until 6/24/99, the rate of time drift on
the computer was about +0.8 seconds per day. However, if the time was not reset since
integration at AIS on 1/14/98 (which is recorded in my integration notes), then the rate of
drift is about +0.4 seconds per day.
The computer was replaced and time service started on 7/30/99. |
Measurements: | twpmwrtipC2.a1: - 23.8 GHz sky signal(tipsky23)
- Ambient temperature(tkair)
- base time(base_time)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Mixer kinetic (physical) temperature(tkxc)
- Actual Azimuth(actaz)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- 23.8 GHz goodness-of-fit coefficient(r23)
- Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Time offset of tweaks from base_time(time_offset)
- Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- 31.4 GHz goodness-of-fit coefficient(r31)
- 23.8 GHz Blackbody signal(bb23)
- 31.4 GHz blac2body+noise injection signal(bbn31)
- Blackbody kinetic temperature(tkbb)
- 23.8 GHz blackbody+noise injection signal(bbn23)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
- Temperature correction coefficient at 31.4 GHz(tc31)
- (tknd)
- 31.4 GHz blackbody(bb31)
- Actual elevation angle(actel)
- Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
- 31.4 GHz sky signal(tipsky31)
twpmwrlosC2.b1: - Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- 23.8 GHz sky signal(sky23)
- Averaged total liquid water along LOS path(liq)
- 23.8 GHz blackbody+noise injection signal(bbn23)
- Blackbody kinetic temperature(tkbb)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Mixer kinetic (physical) temperature(tkxc)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
- 31.4 GHz blac2body+noise injection signal(bbn31)
- base time(base_time)
- Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Sky Infra-Red Temperature(sky_ir_temp)
- Time offset of tweaks from base_time(time_offset)
- 31.4 GHz blackbody(bb31)
- IR Brightness Temperature(ir_temp)
- Actual elevation angle(actel)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- Sky brightness temperature at 23.8 GHz(tbsky23)
- 31.4 GHz sky signal(sky31)
- Sky brightness temperature at 31.4 GHz(tbsky31)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Ambient temperature(tkair)
- (tknd)
- MWR column precipitable water vapor(vap)
- 23.8 GHz Blackbody signal(bb23)
- Temperature correction coefficient at 31.4 GHz(tc31)
- Actual Azimuth(actaz)
|
Subject: | TWP/MWR/C2 - Installation |
DataStreams: | twpmwrlosC2.b1, twpmwrtipC2.a1
|
Description: | The Nauru ARCS was installed during the period September-November
1998. Data were being collected by the end of October, but for the
first several weeks of November, the site was undergoing considerable
change, so data from that period should be used with caution. The
official site dedication occured on November 20. Most on-site
activity ended following the dedication so we will consider November
20 to be the beginning of the Nauru operations. The last members of
the installation team left Nauru on November 24. |
Measurements: | twpmwrtipC2.a1: - 23.8 GHz Blackbody signal(bb23)
- 23.8 GHz sky signal(tipsky23)
- 31.4 GHz blac2body+noise injection signal(bbn31)
- Ambient temperature(tkair)
- Blackbody kinetic temperature(tkbb)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Mixer kinetic (physical) temperature(tkxc)
- Actual Azimuth(actaz)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
- 23.8 GHz blackbody+noise injection signal(bbn23)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- Temperature correction coefficient at 31.4 GHz(tc31)
- 23.8 GHz goodness-of-fit coefficient(r23)
- (tknd)
- Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
- 31.4 GHz blackbody(bb31)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Actual elevation angle(actel)
- Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
- 31.4 GHz goodness-of-fit coefficient(r31)
- 31.4 GHz sky signal(tipsky31)
twpmwrlosC2.b1: - Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Sky Infra-Red Temperature(sky_ir_temp)
- Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- 23.8 GHz sky signal(sky23)
- Averaged total liquid water along LOS path(liq)
- 23.8 GHz blackbody+noise injection signal(bbn23)
- 31.4 GHz blackbody(bb31)
- IR Brightness Temperature(ir_temp)
- Actual elevation angle(actel)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- Blackbody kinetic temperature(tkbb)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Sky brightness temperature at 23.8 GHz(tbsky23)
- Sky brightness temperature at 31.4 GHz(tbsky31)
- 31.4 GHz sky signal(sky31)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Ambient temperature(tkair)
- Mixer kinetic (physical) temperature(tkxc)
- MWR column precipitable water vapor(vap)
- (tknd)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
- 23.8 GHz Blackbody signal(bb23)
- 31.4 GHz blac2body+noise injection signal(bbn31)
- Temperature correction coefficient at 31.4 GHz(tc31)
- Actual Azimuth(actaz)
|
Subject: | TWP/MWR/C2 - thermal instability |
DataStreams: | twpmwrlosC2.b1, twpmwrtipC2.a1
|
Description: | The MWR required an unusually long time to reach thermal stability after a 4-day outage
due to a power failure that damaged the blower/heater assembly. Also during this period,
the heater, which had been replaced, appears to have been on continously, causing the data
to be inappropriately flagged. |
Measurements: | twpmwrtipC2.a1: - 23.8 GHz sky signal(tipsky23)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- Temperature correction coefficient at 31.4 GHz(tc31)
- 31.4 GHz sky signal(tipsky31)
twpmwrlosC2.b1: - Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- 31.4 GHz sky signal(sky31)
- Sky brightness temperature at 31.4 GHz(tbsky31)
- 23.8 GHz sky signal(sky23)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Averaged total liquid water along LOS path(liq)
- MWR column precipitable water vapor(vap)
- Temperature correction coefficient at 31.4 GHz(tc31)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Sky brightness temperature at 23.8 GHz(tbsky23)
|
Subject: | TWP/MWR/C2 - Reprocessed: Revised Retrieval Coefficients |
DataStreams: | twp5mwravgC2.c1, twpmwrlosC2.b1, twpqmemwrcolC2.c1
|
Description: | IN THE BEGINNING (June 1992), the retrieval coefficients used to derive the precipitable
water vapor (PWV) and liquid water path (LWP) from the MWR brightness temperatures were
based on the Liebe and Layton (1987) water vapor and oxygen absorption model and the Grant
(1957) liquid water absorption model.
Following the SHEBA experience, revised retrievals based on the more recent Rosenkranz
(1998) water vapor and oxygen absorption models and the Liebe (1991) liquid waer absorption
model were developed. The Rosenkranz water vapor absorption model resulted a 2 percent
increase in PWV relative to the earlier Liebe and Layton model. The Liebe liquid water
absorption model decreased the LWP by 10% relative to the Grant model. However, the
increased oxygen absorption caused a 0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was
particularly significant for low LWP conditions (i.e. thin clouds encountered at SHEBA).
Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and Clough, TGARS v. 43,
pp 1102-1108, 2005) that the half-width of the 22 GHz water vapor line from the HITRAN
compilation, which is 5 percent smaller than the Liebe and Dillon (1969) half-width used in
Rosenkranz (1998), provided a better fit to the microwave brightness temperature
measurements at 5 frequencies in the range 22-30 GHz, and yielded more accurate retrievals.
Accordingly, revised MWR retrieval coefficients have been developed using MONORTM, which
utilizes the HITRAN compilation for its spectroscopic parameters. These new retrievals
provide 3 percent less PWV and 2.6 percent greater LWP than the previous
retrievals based on Rosenkranz (1998).
The Rosenkranz-based retrieval coefficients became active at TWP.C2 20020427.0600. The
MONORTM-based retrieval coefficients became active at TWP.C2 20050630.2100.
Note: The TWP.C2 data for 19981028-20050630 have been reprocessed to apply the
MONORTM-based retrievals for all time. The reprocessed data were archived 20061003. |
Measurements: | twpqmemwrcolC2.c1: - Ensemble average for MWR vapor in window centered about balloon release(mean_vap_mwr)
- Ensemble average for MWR liquid in window centered about balloon release(mean_liq_mwr)
twp5mwravgC2.c1: - Averaged total liquid water along LOS path(liq)
- MWR column precipitable water vapor(vap)
twpmwrlosC2.b1: - Averaged total liquid water along LOS path(liq)
- MWR column precipitable water vapor(vap)
|
Subject: | TWP/MWR/C2 - Missing data |
DataStreams: | twp5mwravgC2.c1, twpmwrC2.00, twpmwrlosC2.b1, twpmwrtipC2.a1
|
Description: | The heater blower assembly was causing the fuse to blow. The instrument was taken offline
until a replacement arrives. |
Measurements: | twpmwrtipC2.a1: - 23.8 GHz sky signal(tipsky23)
- Ambient temperature(tkair)
- base time(base_time)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Mixer kinetic (physical) temperature(tkxc)
- Actual Azimuth(actaz)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- 23.8 GHz goodness-of-fit coefficient(r23)
- Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Time offset of tweaks from base_time(time_offset)
- Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- lat(lat)
- 31.4 GHz goodness-of-fit coefficient(r31)
- 23.8 GHz Blackbody signal(bb23)
- 31.4 GHz blac2body+noise injection signal(bbn31)
- Blackbody kinetic temperature(tkbb)
- 23.8 GHz blackbody+noise injection signal(bbn23)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
- Temperature correction coefficient at 31.4 GHz(tc31)
- (tknd)
- Dummy altitude for Zeb(alt)
- 31.4 GHz blackbody(bb31)
- Actual elevation angle(actel)
- Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
- lon(lon)
- 31.4 GHz sky signal(tipsky31)
twp5mwravgC2.c1: - Standard deviation about the mean for the 31.4 GHz sky brightness temperature(tbsky31_sdev)
- Averaged total liquid water along LOS path(liq)
- Time offset of tweaks from base_time(time_offset)
- lat(lat)
- Standard deviation about the mean for the total water vapor amount(vap_sdev)
- Standard deviation about the mean for the IR brightness temperature(ir_temp_sdev)
- IR Brightness Temperature(ir_temp)
- base time(base_time)
- Sky brightness temperature at 23.8 GHz(tbsky23)
- Standard deviation about the mean for the 23.8 GHz sky brightness temperature(tbsky23_sdev)
- Dummy altitude for Zeb(alt)
- Fraction of data in averaging interval with water on Teflon window(water_flag_fraction)
- lon(lon)
- Sky brightness temperature at 31.4 GHz(tbsky31)
- Standard deviation about the mean for the total liquid water amount(liq_sdev)
- Number of data points averaged for 23tbsky, 31tbsky, vap & liq(num_obs)
- Number of points included in the ir_temp ensemble(num_obs_irt)
- MWR column precipitable water vapor(vap)
twpmwrC2.00: - null(Raw data stream - documentation not supported)
twpmwrlosC2.b1: - Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- 23.8 GHz sky signal(sky23)
- Averaged total liquid water along LOS path(liq)
- 23.8 GHz blackbody+noise injection signal(bbn23)
- Blackbody kinetic temperature(tkbb)
- Temperature correction coefficient at 23.8 GHz(tc23)
- Mixer kinetic (physical) temperature(tkxc)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
- 31.4 GHz blac2body+noise injection signal(bbn31)
- base time(base_time)
- Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
- Sky Infra-Red Temperature(sky_ir_temp)
- lat(lat)
- lon(lon)
- Time offset of tweaks from base_time(time_offset)
- 31.4 GHz blackbody(bb31)
- IR Brightness Temperature(ir_temp)
- Actual elevation angle(actel)
- Water on Teflon window (1=WET, 0=DRY)(wet_window)
- Sky brightness temperature at 23.8 GHz(tbsky23)
- Sky brightness temperature at 31.4 GHz(tbsky31)
- 31.4 GHz sky signal(sky31)
- Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
- Ambient temperature(tkair)
- (tknd)
- MWR column precipitable water vapor(vap)
- 23.8 GHz Blackbody signal(bb23)
- Dummy altitude for Zeb(alt)
- Temperature correction coefficient at 31.4 GHz(tc31)
- Actual Azimuth(actaz)
|
Subject: | TWP/MWR/C2 - Software Change |
DataStreams: | twpmwrlosC2.b1
|
Description: | The MWR operating software was changed on 19 November 1998 to provide additional
functionality as described below.
NEW FEATURES
1. Faster sampling rate
Standard line-of-sight (LOS) observations can now be acquired at 15-second intervals vs.
20-second intervals previously. (The standard LOS cycle is comprised of one sky sample per
blackbody sample and gain update.)
2. More flexible sampling strategy
Multiple sky observations can be acquired during a LOS cycle, up to 1024 per gain update.
This permits sky samples to be acquired at intervals of 2.67 seconds for improved
temporal resolution of cloud liquid water variations and better coordination with the millimeter
cloud radar during IOPs.
3. Separation of zenith LOS observations from TIP data
When the radiometer is in TIP mode, the zenith LOS observations are now extracted, the PWV
and LWP computed and reported separately in the output file. This eliminates the periods
of missing LOS data during calibration checks/updates.
4. Automatic self-calibration
The software now permits the calibration to be updated at specified intervals or
continuously. In the first case, LOS mode is automatically changed to TIP mode at user-specified
intervals or whenever clear sky conditions occur, the tip data reduced, the calibration
updated, and the radiometer returned to LOS mode without operator intervention. In the
second case, the radiometer is continuously is TIP mode until changed by the operator.
5. Graphical user display
The graphical display is comprised of a status display, a message display, a temperature
plot, a plot of the retrieved PWV and LWP, and (in TIP mode) a plot of the latest tip
curves. |
Measurements: | twpmwrlosC2.b1: - Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
- Ambient temperature(tkair)
- (tknd)
- Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
|