Data Quality Reports for Session: 149614 User: annie1l1pu Completed: 04/22/2013


TABLE OF CONTENTS

DQR IDSubjectData Streams Affected
D110607.6NSA/KAZR/C1 - Polarizer rotatednsakazrciC1.b1, nsakazrgeC1.b1, nsakazr3253C1.a0
D120913.2NSA/KAZR/C1 - PLO FailurensakazrspeccmaskblxpolC1.a0, nsakazrspeccmaskcicopolC1.a0, nsakazrspeccmaskcixpolC1.a0,
nsakazrspeccmaskgecopolC1.a0, nsakazrspeccmaskgexpolC1.a0, nsakazrauxC1.a1,
nsakazrblC1.b1, nsakazrciC1.b1, nsakazrgeC1.b1, nsakazrspeccmaskblcopolC1.a0
D121218.1NSA/KAZR/C1 - Reprocess: Incorrect calibration constantsnsakazrauxC1.a1, nsakazrblC1.b1, nsakazrgeC1.b1


DQRID : D110607.6
Start DateStart TimeEnd DateEnd Time
05/12/2011230007/29/20110400
Subject:
NSA/KAZR/C1 - Polarizer rotated
DataStreams:nsakazrciC1.b1, nsakazrgeC1.b1, nsakazr3253C1.a0
Description:
The cross-polarization returns were higher than the co-polarization returns causing a 
positive linear depolarization ration.  This cannot be correct.  Upon further investigation, 
it was suggested that waveguide going to the antenna feed polarizer was possibly rotated 
by 45 degrees resulting in the antenna transmitting circular polarization rather than 
linear polarization.  Rotating the polarizer in June did not correct the problem.

It turns out that there is a polarizer in the antenna feed.  Rotated the OMT by 45 degrees 
and substituted micro-coax cable instead of waveguide.

During the time covered by this DQR, the "co-polarization" variables are circularly 
polarized opposite of the transmitted polarization.  The "cross-polarization" variables are the 
same circular polarization as the transmitted signal.
Measurements:nsakazrgeC1.b1:
  • Mean doppler velocity, cross-polar(mean_doppler_velocity_xpol)
  • cal_constant_xpol
  • signal_to_noise_ratio_xpol
  • Spectral width, cross-polar(spectral_width_xpol)
  • Mean doppler velocity, copolar(mean_doppler_velocity_copol)
  • Reflectivity, cross-polar(reflectivity_xpol)
  • Reflectivity, copolar(reflectivity_copol)
  • Spectral width, copolar(spectral_width_copol)
  • signal_to_noise_ratio_copol
  • cal_constant_copol

nsakazr3253C1.a0:
  • HLN(VN)

nsakazrciC1.b1:
  • cal_constant_copol
  • cal_constant_xpol
  • Mean doppler velocity, copolar(mean_doppler_velocity_copol)
  • Reflectivity, cross-polar(reflectivity_xpol)
  • signal_to_noise_ratio_xpol
  • Reflectivity, copolar(reflectivity_copol)
  • signal_to_noise_ratio_copol
  • Mean doppler velocity, cross-polar(mean_doppler_velocity_xpol)
  • Spectral width, cross-polar(spectral_width_xpol)
  • Spectral width, copolar(spectral_width_copol)


Back To Table of Contents

DQRID : D120913.2
Start DateStart TimeEnd DateEnd Time
01/29/2012200002/14/20121800
Subject:
NSA/KAZR/C1 - PLO Failure
DataStreams:nsakazrspeccmaskblxpolC1.a0, nsakazrspeccmaskcicopolC1.a0, nsakazrspeccmaskcixpolC1.a0,
nsakazrspeccmaskgecopolC1.a0, nsakazrspeccmaskgexpolC1.a0, nsakazrauxC1.a1,
nsakazrblC1.b1, nsakazrciC1.b1, nsakazrgeC1.b1, nsakazrspeccmaskblcopolC1.a0
Description:
Streaks began showing up in radar data (reflectivity, doppler velocity, spectral width, 
SNR) at semi regular intervals.  Problem was a failed 16.560 GHz Phase Lock Oscillator 
(PLO).  PLO was replaced 20120214.
Measurements:nsakazrspeccmaskgexpolC1.a0:
  • range
  • Spectral Width(spectral_width)
  • Spectrum of raw counts from spectrometer(spectra)
  • Mean Doppler velocity, clutter filtered(mean_doppler_velocity)
  • velocity_bins
  • time
  • signal_to_noise_ratio
  • Daily values of reflectivity on each grid cell(reflectivity)
  • time_offset
  • locator_mask
  • base_time

nsakazrblC1.b1:
  • time
  • signal_to_noise_ratio_copol
  • base_time
  • Reflectivity, cross-polar(reflectivity_xpol)
  • cal_constant_copol
  • signal_to_noise_ratio_xpol
  • Spectral width, copolar(spectral_width_copol)
  • Roll angle reported by tilt table(roll)
  • Pitch angle reported by tilt table(pitch)
  • Reflectivity, copolar(reflectivity_copol)
  • Mean doppler velocity, copolar(mean_doppler_velocity_copol)
  • Spectral width, cross-polar(spectral_width_xpol)
  • time_offset
  • Mean doppler velocity, cross-polar(mean_doppler_velocity_xpol)
  • cal_constant_xpol
  • rx_noise
  • range

nsakazrspeccmaskcixpolC1.a0:
  • velocity_bins
  • Spectrum of raw counts from spectrometer(spectra)
  • Mean Doppler velocity, clutter filtered(mean_doppler_velocity)
  • time
  • locator_mask
  • signal_to_noise_ratio
  • Daily values of reflectivity on each grid cell(reflectivity)
  • range
  • Spectral Width(spectral_width)
  • base_time
  • time_offset

nsakazrauxC1.a1:
  • rx_noise_ch1
  • temp_power_supply
  • rx_noise_ch2
  • processing_mode
  • time
  • rx_gain_ch1
  • rx_gain_ch2
  • power_supply_28V
  • cal_constant_ch2_xpol
  • lock_alarm_360
  • rh_local
  • pdu_status_j1_logic
  • lock_alarm_1620
  • power_supply_5V
  • power_supply_5p2V
  • temp_rf_detector
  • input_12V
  • input_5V
  • temp_lna
  • rh_antenna
  • temp_component_plate
  • tx_power
  • temp_circulator
  • temp_reverse_power
  • twta_status_state
  • cal_constant_ch2_copol
  • input_minus5V
  • temp_antenna
  • timing_mode
  • lock_alarm_16560
  • time_offset
  • temp_outside_air
  • j2_logic
  • fft_taper_type
  • fault_flags
  • temp_noise_diode
  • input_15V
  • temp_local
  • cal_constant_ch1_xpol
  • noise_source_ch2
  • spare_analog_j12_1
  • noise_source_ch1
  • temp_antenna_feedhorn
  • base_time
  • input_8V
  • lock_alarm_120
  • remote_control_enabled
  • cal_constant_ch1_copol
  • is_powered_on

nsakazrspeccmaskcicopolC1.a0:
  • Daily values of reflectivity on each grid cell(reflectivity)
  • time_offset
  • Mean Doppler velocity, clutter filtered(mean_doppler_velocity)
  • signal_to_noise_ratio
  • velocity_bins
  • Spectral Width(spectral_width)
  • locator_mask
  • range
  • Spectrum of raw counts from spectrometer(spectra)
  • time
  • base_time

nsakazrgeC1.b1:
  • time
  • cal_constant_copol
  • Mean doppler velocity, cross-polar(mean_doppler_velocity_xpol)
  • cal_constant_xpol
  • signal_to_noise_ratio_xpol
  • Mean doppler velocity, copolar(mean_doppler_velocity_copol)
  • qc_time
  • time_offset
  • Reflectivity, copolar(reflectivity_copol)
  • Spectral width, copolar(spectral_width_copol)
  • Reflectivity, cross-polar(reflectivity_xpol)
  • rx_noise
  • signal_to_noise_ratio_copol
  • base_time
  • Spectral width, cross-polar(spectral_width_xpol)
  • range

nsakazrspeccmaskblxpolC1.a0:
  • Mean Doppler velocity, clutter filtered(mean_doppler_velocity)
  • Spectral Width(spectral_width)
  • signal_to_noise_ratio
  • Spectrum of raw counts from spectrometer(spectra)
  • time_offset
  • time
  • velocity_bins
  • base_time
  • Daily values of reflectivity on each grid cell(reflectivity)
  • range
  • locator_mask

nsakazrspeccmaskgecopolC1.a0:
  • Daily values of reflectivity on each grid cell(reflectivity)
  • base_time
  • velocity_bins
  • signal_to_noise_ratio
  • Spectral Width(spectral_width)
  • Spectrum of raw counts from spectrometer(spectra)
  • time
  • locator_mask
  • range
  • Mean Doppler velocity, clutter filtered(mean_doppler_velocity)
  • time_offset

nsakazrspeccmaskblcopolC1.a0:
  • locator_mask
  • Spectral Width(spectral_width)
  • signal_to_noise_ratio
  • time_offset
  • Mean Doppler velocity, clutter filtered(mean_doppler_velocity)
  • base_time
  • Daily values of reflectivity on each grid cell(reflectivity)
  • time
  • range
  • velocity_bins
  • Spectrum of raw counts from spectrometer(spectra)

nsakazrciC1.b1:
  • Mean doppler velocity, copolar(mean_doppler_velocity_copol)
  • rx_noise
  • time
  • cal_constant_copol
  • range
  • qc_time
  • Mean doppler velocity, cross-polar(mean_doppler_velocity_xpol)
  • cal_constant_xpol
  • signal_to_noise_ratio_copol
  • signal_to_noise_ratio_xpol
  • time_offset
  • Spectral width, copolar(spectral_width_copol)
  • Reflectivity, cross-polar(reflectivity_xpol)
  • Reflectivity, copolar(reflectivity_copol)
  • Spectral width, cross-polar(spectral_width_xpol)
  • base_time


Back To Table of Contents

DQRID : D121218.1
Start DateStart TimeEnd DateEnd Time
05/12/2011000012/14/20121659
Subject:
NSA/KAZR/C1 - Reprocess: Incorrect calibration constants
DataStreams:nsakazrauxC1.a1, nsakazrblC1.b1, nsakazrgeC1.b1
Description:
The calibration constants for the modes were incorrect.  The coefficients used were

BL: -34.70 dB
GE: -18.69 dB

The correct coefficients are 

BL: -22.21dB
GE: -13.14 dB
Measurements:nsakazrblC1.b1:
  • Reflectivity, cross-polar(reflectivity_xpol)
  • cal_constant_copol
  • Reflectivity, copolar(reflectivity_copol)
  • cal_constant_xpol

nsakazrauxC1.a1:
  • cal_constant_ch1_copol
  • cal_constant_ch1_xpol
  • cal_constant_ch2_xpol
  • cal_constant_ch2_copol

nsakazrgeC1.b1:
  • cal_constant_xpol
  • Reflectivity, cross-polar(reflectivity_xpol)
  • Reflectivity, copolar(reflectivity_copol)
  • cal_constant_copol


Back To Table of Contents



END OF DATA