TWP/VCEIL/C3 - Degraded Sensitivity, Limited Range

The Darwin ceilometer was displaying a cross-talk warning during this
period. This causes degraded sensitivity and the inability of the 
ceilometer to identify cloud heights that are higher the about 2 km.

• Third cloud base height(third_cbh)
• vertical_visibility
• Lowest cloud base height detected.(first_cbh)
• Backscatter(backscatter)
• alt_highest_signal
• Second lowest cloud base height(second_cbh)

• Backscatter(backscatter)
• Second lowest cloud base height(second_cbh)
• Third cloud base height(third_cbh)
• Lowest cloud base height detected.(first_cbh)
• alt_highest_signal
• vertical_visibility

TWP/VCEIL/C3 - Data collection problem

There was a bad connection between the ceilometer and the instrument computer which 
resulted in a small amount of data loss on 8 days during the effected period.  The data that 
were collected are not effected by the problem.  On April 11, 34% of the data was lost and 
on April 1, 4% was lost.  On the remaining 6 days, May 1-6, the amount of data lost was 
less than 2%/day.

• Raw data stream - documentation not supported

• receiver_sensitivity
• status_string
• laser_pulse_energy
• status_flag
• Second lowest cloud base height(second_cbh)
• measurement_parameters
• Lowest cloud base height detected.(first_cbh)
• lon
• alt_highest_signal
• vertical_visibility
• alt
• Backscatter(backscatter)
• laser_temperature
• tilt_angle
• sum_backscatter
• lat
• Third cloud base height(third_cbh)
• range
• time_offset
• window_contamination
• background_light
• detection_status
• base_time

TWP/VCEIL/C3 - Degraded hardware

It appears that the sensitivity of the Darwin ceilometer was degrading over a few month 
period leading up to September 2005.  Beginning on September 16, 2005, the instrument 
shifted to a particularly bad state.  Looking at the backscatter data, I do not see nearly as 
great a day-night difference in the background as I expect and there is very little 
sensitivity to clouds.  There was cross talk error noted with that instrument. The ceilometer 
was replaced on December 12.

• Backscatter(backscatter)
• Second lowest cloud base height(second_cbh)
• Third cloud base height(third_cbh)
• Lowest cloud base height detected.(first_cbh)
• background_light
• alt_highest_signal
• vertical_visibility

TWP/VCEIL/C3 - ceilometer lost sensitivity

ceilometer sesitivity decreased suddenly and only very strong cloud reflections are 
observed in the first kilometer.

• Backscatter(backscatter)
• status_string
• status_flag
• sum_backscatter
• Second lowest cloud base height(second_cbh)
• Third cloud base height(third_cbh)
• range
• Lowest cloud base height detected.(first_cbh)
• detection_status
• background_light
• vertical_visibility

TWP/VCEIL/C3 - low receiver sensitivity

The ceilometer reported frequent receiver alarms. There are periods when the receiver 
sensitivity dropped to about 50%. The problem was corrected by replacing the instrument with 
a spare.

• receiver_sensitivity
• Backscatter(backscatter)
• sum_backscatter
• Second lowest cloud base height(second_cbh)
• Third cloud base height(third_cbh)
• Lowest cloud base height detected.(first_cbh)
• background_light
• alt_highest_signal
• vertical_visibility

TWP/VCEIL/C3 - standard instrument installed

A spare ceilometer without the tropics window option was installed. The manufacturer 
recommends the tropics window be used at +/- 25 deg lattitude to prevent direct solar 
radiation into the laser optics when the instrument pointed at zenith. No significant signal 
degradation is apparent during the autumnal equinox but, as a precaution, the unit was 
replaced with the original with a tropics window.

• Backscatter(backscatter)
• laser_pulse_energy
• laser_temperature
• sum_backscatter
• background_light
• vertical_visibility

TWP/VCEIL/C3 - Reduced sensitivity to high clouds

The instrument produced a significant number of optical cross-talk warnings and displayed 
a reduced capacity to detect high clouds.  The internal cables were inspected, the 
compensation fiber and optics monitor were replaced, the crosstalk compensation was adjusted, 
and the system tested with an optical termination hood, all with no improvement.  While 
waiting for a new receiver board, receiver ribbon cable, and compensation fiber cable from 
Vaisala, a spare ceilometer with a standard, "non-tropics", window was installed.

• receiver_sensitivity
• Second lowest cloud base height(second_cbh)
• Third cloud base height(third_cbh)
• detection_status
• alt_highest_signal

TWP/VCEIL/C3 - Reduced sensitivity to high clouds

The instrument had reduced sensitivity to high clouds.

The instrument produced a significant number of optical cross-talk warnings and displayed 
a reduced capacity to detect high clouds. The window was cleaned and the instrument was 
power-cycled but with no improvement. Diagnostics indicated the problem was with the 
compensation fiber cable. 

The problem was corrected by replacing this standard-window instrument (that was tilted at 
16 degrees) with a tropics unit that became available.

• receiver_sensitivity
• Second lowest cloud base height(second_cbh)
• Third cloud base height(third_cbh)
• alt_highest_signal
• vertical_visibility

TWP/VCEIL/C3 - Reprocess: Incorrect serial_number and sum_backscatter fields

Attribute serial_number: In most cases, this field is not representative of the actual 
serial number of the instrument because the value did not change when an instrument changed 
locations or was replaced with a spare.
   
Variable sum_backscatter: An out-of-range condition for the "sum of detected and 
normalized backscatter" was reported as 0 instead of missing (-9999). The valid range is 0 - 
0.0999 /srad.
   
This DQR also applies to a1 level data.

• sum_backscatter