NSA/CMH/C1 - Data not representative

The CMH at the NS Barrow site was moved from the base of the tower to the top of the Great 
White Building.  This was done to test the communication of the sensor without having to 
use any bit drivers.

• Raw data stream - documentation not supported

• Dew point temperature(dew_pt_temp)
• alt
• base_time
• Relative humidity(relh)
• time_offset
• relh_out_of_range_error
• Temperature, air(air_temp)
• serial_read_error
• lon
• dew_pt_temp_out_of_range_error
• read_timeout_error
• air_temp_out_of_range_error
• lat

NSA/METTWR/C1  -  C1/METTWR PRESSURE DATA MISSING AND INCORRECT

Starting at 0501 UTC on 05/21, pressure readings frequently are out of tolerance.  The 
read timeout value had changed from 250 ms to 150 ms.  Changed the read time out back to 250 
ms.  Unknown as to how read timeout values changed.

• Barometric Pressure(atmos_pressure)

• Barometric Pressure(atmos_pressure)

NSA/TPS/C1 - Reprocess: Incorrect temporal resolution

The data were incorrectly collected and processed at 1 second temporal resolution rather 
than 1 minute resolution.  Data will be reprocessed to average to 1 minute.  Data quality 
are not compromised by this resolution error.

• Precipitation, total daily accumulated(precip_total)
• enclosure_temp
• Temperature, air(air_temp)
• Precipitation rate(precip_rate)
• Mean Wind Speed(wspd)

NSA/MET/C1 - Temp/RH/wind data questionable

New wind sensors and new T/RH probes were being installed during this time period.  The 
tower booms were lowered and much of the data collected were not at listed heights nor were 
the data accurate due to configurations during install.

• qc_wspd_arith_mean
• qc_rh_mean
• qc_wspd_vec_mean
• vapor_pressure_std
• Wind speed vector mean(wspd_vec_mean)
• qc_temp_mean
• temp_std
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_mean
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• qc_wdir_vec_mean
• Mean Air Temperature or Hardware Error(temp_mean)
• vapor_pressure_mean
• wdir_vec_std
• qc_vapor_pressure_mean
• qc_dew_point_mean
• trh_err_code
• dew_point_std
• rh_std

• wdir_vec_std
• qc_wspd_arith_mean
• qc_temp_mean
• trh_err_code
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wdir_vec_mean
• dew_point_mean
• Mean Air Temperature or Hardware Error(temp_mean)
• temp_std
• Wind speed vector mean(wspd_vec_mean)
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_std
• rh_std
• qc_rh_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• vapor_pressure_mean
• vapor_pressure_std
• qc_wspd_vec_mean
• qc_dew_point_mean
• qc_vapor_pressure_mean

NSA/MET/C1 - PWS data missing due to snow impaction

Blizzard conditions caused the optics to become impacted with snow and ice rendering the 
Present Weather Detector inoperative.

• qc_pws_cumul_snow
• qc_pws_pw_code_15min
• qc_pws_precip_rate_mean_1min
• qc_pws_cumul_rain
• PWS 10 minute mean visibility(pws_vis_mean_10min)
• pws_err_code
• qc_pws_vis_mean_1min
• pws_cumul_rain
• pws_pw_code_1hr
• Rain, surface, 1-min avg(pws_precip_rate_mean_1min)
• pws_cumul_snow
• pws_pw_code_15min
• qc_pws_pw_code_inst
• pws_pw_code_inst
• qc_pws_pw_code_1hr
• qc_pws_err_code
• qc_pws_vis_mean_10min
• PWS 1 minute mean visibility(pws_vis_mean_1min)

NSA/MET/C1 - Wind data intermittent

There was a loose wire on the serial data multiplexer causing the wind data to become 
missing during high wind situations.  The high winds caused the enclosure to vibrate making 
the connection intermittent.

• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wspd_arith_mean
• qc_wspd_vec_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• qc_wdir_vec_mean
• Wind speed vector mean(wspd_vec_mean)
• wdir_vec_std

• wdir_vec_std
• qc_wspd_arith_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• qc_wspd_vec_mean
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wdir_vec_mean
• Wind speed vector mean(wspd_vec_mean)

NSA/MET/C1 - CMH data missing

The data from the CMH was missing during these times due to a failing logic board.  The 
board was replaced.

• cmh_dew_point
• qc_cmh_dew_point
• qc_cmh_rh
• cmh_temp
• cmh_vapor_pressure
• qc_cmh_vapor_pressure
• qc_cmh_sat_vapor_pressure
• qc_cmh_temp
• cmh_sat_vapor_pressure
• cmh_rh

NSA/MET/C1 - Met data incorrect during calibration

All met data from the tower booms (temp, RH, winds and derived variables) were incorrect 
due to the booms being lowered from their measurement heights.  Additionally, the 
scaffolding was located directly adjacent to the booms affecting the wind field and the Temp/RH 
data.

• qc_wspd_arith_mean
• qc_rh_mean
• qc_wspd_vec_mean
• vapor_pressure_std
• Wind speed vector mean(wspd_vec_mean)
• qc_temp_mean
• temp_std
• qc_time
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_mean
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• qc_wdir_vec_mean
• Mean Air Temperature or Hardware Error(temp_mean)
• vapor_pressure_mean
• wdir_vec_std
• qc_vapor_pressure_mean
• qc_dew_point_mean
• trh_err_code
• dew_point_std
• rh_std

• wdir_vec_std
• qc_wspd_arith_mean
• qc_temp_mean
• trh_err_code
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wdir_vec_mean
• dew_point_mean
• Mean Air Temperature or Hardware Error(temp_mean)
• temp_std
• Wind speed vector mean(wspd_vec_mean)
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_std
• rh_std
• qc_rh_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• vapor_pressure_mean
• vapor_pressure_std
• qc_wspd_vec_mean
• qc_dew_point_mean
• qc_vapor_pressure_mean

NSA/MET/C1 - PWS calibration

The PWS was undergoing calibration. Any data collected during this time is not 
representative of the atmospheric state.

• qc_pws_cumul_snow
• qc_pws_pw_code_15min
• qc_pws_precip_rate_mean_1min
• qc_pws_cumul_rain
• PWS 10 minute mean visibility(pws_vis_mean_10min)
• pws_err_code
• qc_pws_vis_mean_1min
• pws_cumul_rain
• pws_pw_code_1hr
• Rain, surface, 1-min avg(pws_precip_rate_mean_1min)
• pws_cumul_snow
• pws_pw_code_15min
• qc_pws_pw_code_inst
• pws_pw_code_inst
• qc_pws_pw_code_1hr
• qc_pws_err_code
• qc_pws_vis_mean_10min
• PWS 1 minute mean visibility(pws_vis_mean_1min)

NSA/MET/C1 - CMH calibration

CMH data missing due to removal of the sensor for annual calibration.

• cmh_dew_point
• qc_cmh_dew_point
• qc_cmh_rh
• cmh_temp
• cmh_vapor_pressure
• qc_cmh_vapor_pressure
• qc_cmh_sat_vapor_pressure
• qc_cmh_temp
• cmh_sat_vapor_pressure
• cmh_rh

NSA/MET/C1 - 2m RH values incorrect

The new t/rh probe installed during annual calibrations and checks began to exhibit 
readings that were biased high compared to the Chilled Mirror Hygrometer.  In high RH 
conditions the sensor would consistently report RH values in excess of 105%.  Comparisons to the 
other tower levels also suggested that the 2m level RH data is suspect.

• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_mean
• qc_rh_mean
• vapor_pressure_std
• vapor_pressure_mean
• qc_dew_point_mean
• dew_point_std
• rh_std

• rh_std
• qc_rh_mean
• vapor_pressure_mean
• vapor_pressure_std
• dew_point_mean
• qc_dew_point_mean
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_std
• qc_vapor_pressure_mean

NSA/TWR/C1 - 40m T/RH Sensor Failure

40m RH data were very noisy after tower maintenance.  Following system re-boot, RH data 
were too high. Sensor was replaced.

• dew_point_mean
• qc_dew_point_mean
• rh_std
• qc_rh_mean
• vapor_pressure_mean
• vapor_pressure_std
• dew_point_std
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• qc_vapor_pressure_mean

NSA/TWR/C1 - 40m and 20m Data Incorrect

A power distribution problem required us to shut down power to the 40m level.  All T/RH 
were missing and the 40m wind sensor did not have heat to remove any ice build up.  All 
wind data from the 40m level should be viewed critically before use.  The 20m T/RH sensor 
was power spike when the problem occurred causing this sensor to become erratic.  
See D100302.2 for the continuation of the 40m problem.

• wdir_vec_std
• rh_std
• qc_rh_mean
• qc_wspd_arith_mean
• qc_temp_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• vapor_pressure_mean
• vapor_pressure_std
• qc_wspd_vec_mean
• trh_err_code
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wdir_vec_mean
• dew_point_mean
• qc_dew_point_mean
• Mean Air Temperature or Hardware Error(temp_mean)
• temp_std
• Wind speed vector mean(wspd_vec_mean)
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• dew_point_std
• qc_vapor_pressure_mean

NSA/MET/C1 - CMH and 10m winds failure

At 0513GMT on 1/23 the atmos_pressure and CMH - temp, RH, DP & Sat. VP changed abruptly to 
unlikely values. The 10m winds failed at 1420GMT.

The CMH was repaired on 02/04/2010 at 2254GMT and the 10m winds sensor was replaced on 
02/05/2010 at 2100GMT.

• cmh_dew_point
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wspd_arith_mean
• qc_cmh_dew_point
• qc_wspd_vec_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• cmh_vapor_pressure
• qc_cmh_temp
• cmh_sat_vapor_pressure
• qc_wdir_vec_mean
• Wind speed vector mean(wspd_vec_mean)
• wdir_vec_std
• qc_cmh_rh
• cmh_temp
• qc_cmh_vapor_pressure
• qc_cmh_sat_vapor_pressure
• cmh_rh

NSA/TWR/C1 - Wind sensor data failures

The wind speed and direction values for 2m, 10m and 20m dropped to zero at 14:20 GMT. The 
cause was a power failure due to failed power line.  Power spikes caused the wind sensors 
to revert to default settings for communications and measurements. The following is a 
list of dates that the various sensors came back online:
  2m wind problem ending on 01/28/2010 @ 2330GMT
 20m wind problem ending on 02/04/2010 @ 2230GMT
 10m wind problem ending on 02/05/2010 @ 2100GMT
  
40m winds were already failing and documented in DQPR 2262 and PIF P091030.1.  

The MET system was also affected and documented in DQPR 2337.

• wdir_vec_std
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wdir_vec_mean
• qc_wspd_arith_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)
• Wind speed vector mean(wspd_vec_mean)
• qc_wspd_vec_mean

NSA/MET/C1 - CMH Data Missing

The GFCI had tripped causing the CMH to lose power.  All CMH variables are missing except 
CMHRH which reports 100% for the entire time.

• cmh_dew_point
• qc_cmh_dew_point
• qc_cmh_rh
• cmh_temp
• cmh_vapor_pressure
• qc_cmh_vapor_pressure
• qc_cmh_sat_vapor_pressure
• qc_cmh_temp
• cmh_sat_vapor_pressure
• cmh_rh

NSA/MET/C1 - CMH Sent to Vendor for Repair

CMH connector on the transmitter enclosure that goes to the head unit degraded and failed. 
 System was removed and sent to the manufacturer for repair.

• cmh_dew_point
• qc_cmh_dew_point
• qc_cmh_rh
• cmh_temp
• cmh_vapor_pressure
• qc_cmh_vapor_pressure
• qc_cmh_sat_vapor_pressure
• qc_cmh_temp
• cmh_sat_vapor_pressure
• cmh_rh

NSA/MET/C1 - CMH offline

CMH removed for repair.

• cmh_dew_point
• qc_cmh_dew_point
• qc_cmh_rh
• cmh_temp
• cmh_vapor_pressure
• qc_cmh_vapor_pressure
• qc_cmh_sat_vapor_pressure
• qc_cmh_temp
• cmh_sat_vapor_pressure
• cmh_rh

NSA/MET/C1 - 10m wind sensor offline

The 10m wind sensor values were 0 m/s and 000 for wind direction. The sensor lost 
communications.

• qc_wdir_vec_mean
• Wind speed, lower, 1-min avg(wspd_arith_mean)
• qc_wspd_arith_mean
• Wind speed vector mean(wspd_vec_mean)
• wdir_vec_std
• qc_wspd_vec_mean
• Wind direction, vector, lower, 1-min avg(wdir_vec_mean)

NSA/MET/C1 - 20m T/RH sensor failure

The 20m temperature and RH were erratic and incorrect resulting in incorrect vapor 
pressure calculations.  The sensor was damaged by voltage spikes on the power lines.

• dew_point_mean
• rh_std
• Mean Air Temperature or Hardware Error(temp_mean)
• temp_std
• vapor_pressure_mean
• vapor_pressure_std
• dew_point_std
• Humidity, relative, at 2-m height, 1-min avg(rh_mean)
• trh_err_code