TWP/SMET/C3 - Barometer Data Incorrect

The barometer data was incorrect or missing due to water intrusion.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Water in enclosure

Data became erratic and unreasonable after water intrusion into the enclosure.

• Precipitation mean(precip_mean)
• Vapor pressure standard deviation(vappress_sd)
• Precipitation maximum(precip_max)
• Mean Relative Humidity(relh_mean)
• Mean Air Temperature or Hardware Error(temp_mean)
• Precipitation standard deviation(precip_sd)
• Vapor pressure mean(vappress_mean)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• precipitation minimum(precip_min)
• Std Dev of Air Temperature(temp_sd)

TWP/SMET/C3 - Upper wind speed artificially slow

The upper wind measurement was consistently slower by around 0.5 - 1 m/s than the lower 
wind measurement.  The bearings on the upper wind measurement were binding.

• Upper sensor, wind speed maximum(up_spd_max)
• Upper sensor, wind speed arithmetic average(up_spd_arith_avg)
• Upper sensor, wind speed minimum(up_spd_min)
• Upper sensor, wind speed vector average(up_spd_vec_avg)
• Upper sensor, wind speed standard deviation(up_spd_sd)

TWP/SMET/C3 - ORG overestimated rainfall

Optical rain gauge (ORG) measured approximately 10mm higher than two co-located tipping 
bucket rain gauges and a co-located disdrometer.  The ORG is typically higher but usually 
not by an order of magnitude.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - Wind Speed data contain offset due to induced voltage

The marine model of the RM Young wind sensor needs twisted pair shielded cable.  The 
manufacturer did not originally supply the pigtail with twisted pair shielded cable.  Use of 
twisted pair shielded cable for the rest of the cable run to the logger was also not 
specified.  This caused an induced voltage in the wind speed line from the wind direction 
excitation.  The induced voltage varied from sensor to sensor and probably changed anytime 
the cable was replaced or parts of the wind sensor were repaired or replaced. The induced 
voltage has been seen to vary from 0.15 m/s to as much as 1.08 m/s.

• Upper sensor, wind speed maximum(up_spd_max)
• Lower sensor, wind speed minimum(lo_spd_min)
• Lower sensor, wind speed standard deviation(lo_spd_sd)
• Lower sensor, wind speed maximum(lo_spd_max)
• Upper sensor, wind speed arithmetic average(up_spd_arith_avg)
• Lower sensor, wind speed vector average(lo_spd_vec_avg)
• Upper sensor, wind speed minimum(up_spd_min)
• Lower sensor, wind speed arithmetic average(lo_spd_arith_avg)
• Upper sensor, wind speed vector average(up_spd_vec_avg)
• Upper sensor, wind speed standard deviation(up_spd_sd)

TWP/SMET/C3 - Reprocess: Temperature Biased low by 1.06 Degrees

The temperature of the SMET system was biased low by 1.06 Deg C due to a non-precision 
resistor being used int he measurement circuit.  The data will be reprocessed.  Saturation 
Vapor pressure and Vapor pressure will have to be reprocessed also.

Add 1.06 degrees to the temperature data.  

Correct Sat Vap Press using the Buck approximation:
   Es = 6.1121exp((17.502*T)/(240.97 + T) 
where T is the temperature in C.  

Correct Vapor pressure using: E = (RH*Es)/100

• Vapor pressure standard deviation(vappress_sd)
• Mean Air Temperature or Hardware Error(temp_mean)
• Vapor pressure mean(vappress_mean)
• Std Dev of Air Temperature(temp_sd)