SGP/MWR/B1  - min/max/delta values incorrect

The values of valid_min, valid_max, and valid_delta for fields tkxc and tknd were 
incorrect. They should be 303, 333, and 0.5 K, respectively.

• (tknd)
• Mixer kinetic (physical) temperature(tkxc)

SGP/MWR/B4  - min/max/delta values incorrect

The values of valid_min, valid_max, and valid_delta for fields tkxc and tknd were 
incorrect. They should be 303, 333, and 0.5 K, respectively.

• Mixer kinetic (physical) temperature(tkxc)
• (tknd)

SGP/MWR/B6  - min/max/delta values incorrect

The values of valid_min, valid_max, and valid_delta for fields tkxc and tknd were 
incorrect. They should be 303, 333, and 0.5 K, respectively.

• Mixer kinetic (physical) temperature(tkxc)
• (tknd)

SGP/MWR/B1 - thermal instability

During periods of high ambient temperature, the instrument may have been thermally 
unstable.

• Sky brightness temperature at 23.8 GHz(tbsky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Averaged total liquid water along LOS path(liq)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• MWR column precipitable water vapor(vap)
• Sky brightness temperature at 23.8 GHz(tbsky23)

SGP/MWR/B6  - thermal instability

During periods of high ambient temperature, the instrument may have been thermally 
unstable.

• MWR column precipitable water vapor(vap)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)

SGP/MWR/B4 - no air temperature signal

When the new blower was upgraded by Radiometrics and reinstalled on the MWR, the air 
temperature sensor failed to properly report. It was determined that the wires carrying the 
signal to the analog board did not conform to the standard expected by the upgraded blower. 
The problem was corrected by changing the wiring and modifying the MWR software to read 
the signal from the appropriate corresponding channel.

• Ambient temperature(tkair)

• Ambient temperature(tkair)

SGP/MWR/B1 - Reprocess: Revised Retrieval Coefficients

IN THE BEGINNING (June 1992), the retrieval coefficients used to derive the precipitable 
water vapor (PWV) and liquid water path (LWP) from the MWR brightness temperatures were 
based on the Liebe and Layton (1987) water vapor and oxygen absorption model and the Grant 
(1957) liquid water absorption model.

Following the SHEBA experience, revised retrievals based on the more recent Rosenkranz 
(1998) water vapor and oxygen absorption models and the Liebe (1991) liquid waer absorption 
model were developed.  The Rosenkranz water vapor absorption model resulted a 2 percent 
increase in PWV relative to the earlier Liebe and Layton model.  The Liebe liquid water 
absorption model decreased the LWP by 10% relative to the Grant model.  However, the 
increased oxygen absorption caused a 0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was 
particularly significant for low LWP conditions (i.e. thin clouds encountered at SHEBA).

Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and Clough, TGARS v. 43, 
pp 1102-1108, 2005) that the half-width of the 22 GHz water vapor line from the HITRAN 
compilation, which is 5 percent smaller than the Liebe and Dillon (1969) half-width used in 
Rosenkranz (1998), provided a better fit to the microwave brightness temperature 
measurements at 5 frequencies in the range 22-30 GHz, and yielded more accurate retrievals. 
Accordingly, revised MWR retrieval coefficients have been developed using MONORTM, which 
utilizes the HITRAN compilation for its spectroscopic parameters.  These new retrievals 
provide 3 percent less PWV and 2.6 percent greater LWP than the previous retrievals based on 
Rosenkranz (1998).

Although the MWR data will be reprocessed to apply the new monortm-based retrievals, for 
most purposes it will be sufficient to correct the data using the following factors:

PWV_MONORTM = 0.9695 * PWV_ROSENKRANZ
LWP_MONORTM = 1.026  * LWP_ROSENKRANZ

The Rosenkranz-based retrieval coefficients became active at SGP.B1 20020412.1600.  The 
MONORTM-based retrieval coefficients became active at SGP.B1 20050624.2100.

Note: a reprocessing effort is already underway to apply the Rosenkranz-based retrieval 
coefficients to all MWR prior to April 2002.  An additional reprocessing task will be 
undertaken to apply the MONORTM retrieval to all MWR data when the first is completed.  Read 
reprocessing comments in the netcdf file header carefully to ensure you are aware which 
retrieval is in play.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)

• Ensemble average for MWR liquid in window centered about balloon release(mean_liq_mwr)
• Ensemble average for MWR vapor in window centered about balloon release(mean_vap_mwr)

SGP/MWR/B4 - Reprocess: Revised Retrieval Coefficients

IN THE BEGINNING (June 1992), the retrieval coefficients used to derive the precipitable 
water vapor (PWV) and liquid water path (LWP) from the MWR brightness temperatures were 
based on the Liebe and Layton (1987) water vapor and oxygen absorption model and the Grant 
(1957) liquid water absorption model.

Following the SHEBA experience, revised retrievals based on the more recent Rosenkranz 
(1998) water vapor and oxygen absorption models and the Liebe (1991) liquid waer absorption 
model were developed.  The Rosenkranz water vapor absorption model resulted a 2 percent 
increase in PWV relative to the earlier Liebe and Layton model.  The Liebe liquid water 
absorption model decreased the LWP by 10% relative to the Grant model.  However, the 
increased oxygen absorption caused a 0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was 
particularly significant for low LWP conditions (i.e. thin clouds encountered at SHEBA).

Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and Clough, TGARS v. 43, 
pp 1102-1108, 2005) that the half-width of the 22 GHz water vapor line from the HITRAN 
compilation, which is 5 percent smaller than the Liebe and Dillon (1969) half-width used in 
Rosenkranz (1998), provided a better fit to the microwave brightness temperature 
measurements at 5 frequencies in the range 22-30 GHz, and yielded more accurate retrievals. 
Accordingly, revised MWR retrieval coefficients have been developed using MONORTM, which 
utilizes the HITRAN compilation for its spectroscopic parameters.  These new retrievals 
provide 3 percent less PWV and 2.6 percent greater LWP than the previous retrievals based on 
Rosenkranz (1998).

Although the MWR data will be reprocessed to apply the new monortm-based retrievals, for 
most purposes it will be sufficient to correct the data using the following factors:

PWV_MONORTM = 0.9695 * PWV_ROSENKRANZ
LWP_MONORTM = 1.026  * LWP_ROSENKRANZ

The Rosenkranz-based retrieval coefficients became active at SGP.B4 20020415.2300.  The 
MONORTM-based retrieval coefficients became active at SGP.B4 20050624.2100.

Note: a reprocessing effort is already underway to apply the Rosenkranz-based retrieval 
coefficients to all MWR prior to April 2002.  An additional reprocessing task will be 
undertaken to apply the MONORTM retrieval to all MWR data when the first is completed. Read 
reprocessing comments in the netcdf file header carefully to ensure you are aware which 
retrieval is in play.

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)

• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)

• Ensemble average for MWR vapor in window centered about balloon release(mean_vap_mwr)
• Ensemble average for MWR liquid in window centered about balloon release(mean_liq_mwr)

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

SGP/MWR/B6 - Reprocess: Revised Retrieval Coefficients

IN THE BEGINNING (June 1992), the retrieval coefficients used to derive 
the precipitable water vapor (PWV) and liquid water path (LWP) from the 
MWR brightness temperatures were based on the Liebe and Layton (1987) 
water vapor and oxygen absorption model and the Grant (1957) liquid 
water absorption model.

Following the SHEBA experience, revised retrievals based on the more 
recent Rosenkranz (1998) water vapor and oxygen absorption models and 
the Liebe (1991) liquid waer absorption model were developed.  The 
Rosenkranz water vapor absorption model resulted a 2 percent increase 
in PWV relative to the earlier Liebe and Layton model.  The Liebe 
liquid water absorption model decreased the LWP by 10% relative to the 
Grant model.  However, the increased oxygen absorption caused a 
0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was particularly 
significant for low LWP conditions (i.e. thin clouds encountered at 
SHEBA).

Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and 
Clough, TGARS v. 43, pp 1102-1108, 2005) that the half-width of the 
22 GHz water vapor line from the HITRAN compilation, which is 5 percent 
smaller than the Liebe and Dillon (1969) half-width used in Rosenkranz 
(1998), provided a better fit to the microwave brightness temperature 
measurements at 5 frequencies in the range 22-30 GHz, and yielded more 
accurate retrievals. Accordingly, revised MWR retrieval coefficients 
have been developed using MONORTM, which utilizes the HITRAN compilation 
for its spectroscopic parameters.  These new retrievals provide 3 
percent less PWV and 2.6 percent greater LWP than the previous 
retrievals based on Rosenkranz (1998).

Although the MWR data will be reprocessed to apply the new monortm-based 
retrievals, for most purposes it will be sufficient to correct the data 
using the following factors:

PWV_MONORTM = 0.9695 * PWV_ROSENKRANZ
LWP_MONORTM = 1.026  * LWP_ROSENKRANZ

The Rosenkranz-based retrieval coefficients became active at SGP.B6 
20020416.2200.  The MONORTM-based retrieval coefficients became active 
at SGP.B6 20050624.1942.

Note: a reprocessing effort is already underway to apply the 
Rosenkranz-based retrieval coefficients to all MWR prior to April 
2002.  An additional reprocessing task will be undertaken to apply 
the MONORTM retrieval to all MWR data when the first is completed. 
Read reprocessing comments in the netcdf file header carefully to 
ensure you are aware which retrieval is in play.

• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Ensemble average for MWR liquid in window centered about balloon release(mean_liq_mwr)
• Ensemble average for MWR vapor in window centered about balloon release(mean_vap_mwr)

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)

SGP/MWR/B1 - New software version (4.15) installed

A problem began with the installation of MWR.EXE version 4.12 in July 2002. The software 
had been upgraded from a "DOS" to a "Windows"-compiled program to address an earlier 
problem.  The software upgrade corrected the earlier problem but introduced a new one that 
caused line-of-sight observing cycles to be skipped, a 15% reduction in the number of tip 
curves, and saturation of CPU usage. Software versions 4.13 and 4.14 also produced these 
problems.

The new MWR software, version 4.15, was installed on 9/13/2005 at 21:25. As a consequence 
of this upgrade, the tip curve frequency increased. The tip cycle time decreased from 
~60s to ~50s.

• Blackbody kinetic temperature(tkbb)
• 23.8 GHz sky signal(tipsky23)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.4 GHz blackbody(bb31)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Mixer kinetic (physical) temperature(tkxc)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• (tknd)
• Ambient temperature(tkair)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz sky signal(tipsky31)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.4 GHz blac2body+noise injection signal(bbn31)

• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Sky Infra-Red Temperature(sky_ir_temp)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Ambient temperature(tkair)
• IR Brightness Temperature(ir_temp)
• 23.8 GHz sky signal(sky23)
• Averaged total liquid water along LOS path(liq)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz sky signal(sky31)
• (tknd)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 31.4 GHz blackbody(bb31)
• Mixer kinetic (physical) temperature(tkxc)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Blackbody kinetic temperature(tkbb)
• MWR column precipitable water vapor(vap)
• 23.8 GHz Blackbody signal(bb23)

SGP/MWR/B4 - New software version (4.15) installed

A problem began with the installation of MWR.EXE version 4.12 in July 2002. The software 
had been upgraded from a "DOS" to a "Windows"-compiled program to address an earlier 
problem.  The software upgrade corrected the earlier problem but introduced a new one that 
caused line-of-sight observing cycles to be skipped, a 15% reduction in the number of tip 
curves, and saturation of CPU usage. Software versions 4.13 and 4.14 also produced these 
problems.

The new MWR software, version 4.15, was installed on 9/13/2005. As a consequence of this 
upgrade, the tip curve frequency increased. The tip cycle time decreased from ~60s to ~50s.

• Averaged total liquid water along LOS path(liq)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Sky Infra-Red Temperature(sky_ir_temp)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blackbody(bb31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Ambient temperature(tkair)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• (tknd)
• Blackbody kinetic temperature(tkbb)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• MWR column precipitable water vapor(vap)
• IR Brightness Temperature(ir_temp)
• 31.4 GHz sky signal(sky31)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Mixer kinetic (physical) temperature(tkxc)

• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• Mixer kinetic (physical) temperature(tkxc)
• 23.8 GHz Blackbody signal(bb23)
• (tknd)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 31.4 GHz blackbody(bb31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Blackbody kinetic temperature(tkbb)
• 23.8 GHz sky signal(tipsky23)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Ambient temperature(tkair)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)

SGP/MWR/B6 - New software version (4.15) installed

A problem began with the installation of MWR.EXE version 4.12 in July 2002. The software 
had been upgraded from a "DOS" to a "Windows"-compiled program to address an earlier 
problem.  The software upgrade corrected the earlier problem but introduced a new one that 
caused line-of-sight observing cycles to be skipped, a 15% reduction in the number of tip 
curves, and saturation of CPU usage. Software versions 4.13 and 4.14 also produced these 
problems.

The new MWR software, version 4.15, was installed on 9/23/2005. As a consequence of this 
upgrade, the tip curve frequency increased. The tip cycle time decreased from ~60s to ~50s.

• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Ambient temperature(tkair)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• (tknd)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 23.8 GHz sky signal(tipsky23)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blackbody(bb31)
• Blackbody kinetic temperature(tkbb)
• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 31.4 GHz(tc31)

• IR Brightness Temperature(ir_temp)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• 23.8 GHz sky signal(sky23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• MWR column precipitable water vapor(vap)
• Mixer kinetic (physical) temperature(tkxc)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Sky Infra-Red Temperature(sky_ir_temp)
• 31.4 GHz blackbody(bb31)
• Ambient temperature(tkair)
• Blackbody kinetic temperature(tkbb)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Temperature correction coefficient at 23.8 GHz(tc23)
• (tknd)
• 31.4 GHz sky signal(sky31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)

SGP/MWR/B4 - Missing data

Data are missing and unrecoverable.

• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Dummy altitude for Zeb(alt)
• Time offset of tweaks from base_time(time_offset)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• lon(lon)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Blackbody kinetic temperature(tkbb)
• MWR column precipitable water vapor(vap)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• 31.4 GHz sky signal(sky31)
• IR Brightness Temperature(ir_temp)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Mixer kinetic (physical) temperature(tkxc)
• lat(lat)
• Averaged total liquid water along LOS path(liq)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Sky Infra-Red Temperature(sky_ir_temp)
• 31.4 GHz blackbody(bb31)
• Ambient temperature(tkair)
• (tknd)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• base time(base_time)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)

• Mixer kinetic (physical) temperature(tkxc)
• (tknd)
• Temperature correction coefficient at 31.4 GHz(tc31)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• Blackbody kinetic temperature(tkbb)
• Actual Azimuth(actaz)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• lat(lat)
• 23.8 GHz Blackbody signal(bb23)
• Dummy altitude for Zeb(alt)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Actual elevation angle(actel)
• Time offset of tweaks from base_time(time_offset)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 31.4 GHz blackbody(bb31)
• base time(base_time)
• lon(lon)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Ambient temperature(tkair)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)

SGP/MWR/B1 - Missing data

Data are missing and unrecoverable.

• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Sky Infra-Red Temperature(sky_ir_temp)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Dummy altitude for Zeb(alt)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Ambient temperature(tkair)
• IR Brightness Temperature(ir_temp)
• 23.8 GHz sky signal(sky23)
• Averaged total liquid water along LOS path(liq)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• lon(lon)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• lat(lat)
• 31.4 GHz sky signal(sky31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• (tknd)
• Time offset of tweaks from base_time(time_offset)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 31.4 GHz blackbody(bb31)
• Mixer kinetic (physical) temperature(tkxc)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• base time(base_time)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Blackbody kinetic temperature(tkbb)
• MWR column precipitable water vapor(vap)
• 23.8 GHz Blackbody signal(bb23)