SGP/EBBR/E26 - Spark Gap Bad, Pressure Incorrect

In a trip to E26, I found that a bad spark gap through which the barometer was powered was 
causing pressure measurements to be incorrect.  The pressure readings oscillated with 
the voltage of the EBBR battery.  During daytime the voltage and thus the pressure would 
increase and vice versa during dark hours.

Apparently only the positive side of the power supply was properly connected through the 
spark gap and thus the voltage received by the pressure sensor was lower than required to 
power it properly.  Under this condition the perssure measurement varies with voltage 
level.  The pressure measurements therefore had a diurnal signature and usually were 
incorrect.  

The decreased pressure during most times would cause latent heat flux to be slightly 
overestimated and sensible heat flux to be slightly underestimated.

• Atmospheric pressure(mv_pres)

• Retrieved pressure profile(pres)

• ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
• latent heat flux(e)
• Retrieved pressure profile(pres)
• h(h)

SGP/EBBR/E20 - AEM Failure

The AEM hung inbetween positions; home signals were zero.

The AEM fuse kept blowing, most likely because of worn
rails or sleeves.  This condition may reoccur.

• bottom vapor pressure(vp_bot)
• Temperature of the top humidity chamber(thum_top)
• Bottom humidity(hum_bot)
• top air temperature(tair_top)
• Temperature of bottom humidity sensor chamber(thum_bot)
• ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
• latent heat flux(e)
• Top humidity(hum_top)
• h(h)
• top vapor pressure(vp_top)
• bottom air temperature(tair_bot)

• Right air temperature(tair_r)
• Left air temperature(tair_l)

• Bottom humidity(hum_bot)
• Temperature of the top humidity chamber(thum_top)
• bottom vapor pressure(vp_bot)
• top air temperature(tair_top)
• bottom air temperature(tair_bot)
• Temperature of bottom humidity sensor chamber(thum_bot)
• Top humidity(hum_top)
• top vapor pressure(vp_top)

SGP/EBBR/E15 - Soil Moisture Coefficients Incorrect

The soil Moisture coefficients used for E15 were incorrect from the time of
installation of the system in program version 8.  On 9 July 02 parameter 4  (an offset 
value) of program step 136 was changed from 9.5264 to the correct value 0.95264 (this error 
had been made by the vendor). The error masked the real problem (wrong soil type) and 
after 9 July 02 resulted in very low soil moisture measurements.  The coefficients used were 
for coarse sand.  On 28 Sep 04 I visited the E15 site and found the soil type a fine 
sandy clay or fine sandy loam.  I changed the coefficients  at 1509 GMT to those for a very 
fine sandy loam; this produced reasonable soil moistures for the soil type.

The old coefficients in parameters 4 through 9 for step 136 of the program were: 0.95264, 
-6.7859, 36.224, -58.619, 25.073, 4.2278

The new coefficients are: 10.241, -27.943, 49.523, -12.648, -52.643, 38.054

• volumetric soil moisture, site 3(sm3)
• soil heat flow, site 3(g3)
• 0-5 cm change in soil heat storage with time, site 3(ces3)
• 0-5 cm change in soil heat storage with time, site 4(ces4)
• volumetric soil moisture, site 2(sm2)
• soil heat flow, site 2(g2)
• latent heat flux(e)
• volumetric soil moisture, site 1(sm1)
• 0-5 cm change in soil heat storage with time, site 5(ces5)
• soil heat flow, site 1(g1)
• 0-5 cm change in soil heat storage with time, site 2(ces1)
• soil heat flow, site 5(g5)
• average surface soil heat flow(ave_shf)
• volumetric soil moisture, site 4(sm4)
• 0-5 cm change in soil heat storage with time, site 2(ces2)
• h(h)
• soil heat flow, site 4(g4)
• volumetric soil moisture, site 5(sm5)

SGP/EBBR/E18 - 6 Month Checks

Many measurements were incorrect while the AEM was positioned with both aspirators at the 
same height for comparison checks.

• Temperature of bottom humidity sensor chamber(thum_bot)
• top air temperature(tair_top)
• Top humidity(hum_top)
• top vapor pressure(vp_top)
• Temperature of the top humidity chamber(thum_top)
• bottom air temperature(tair_bot)
• Bottom humidity(hum_bot)
• bottom vapor pressure(vp_bot)

• top air temperature(tair_top)
• latent heat flux(e)
• bottom vapor pressure(vp_bot)
• ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
• h(h)
• Bottom humidity(hum_bot)
• Temperature of the top humidity chamber(thum_top)
• Temperature of bottom humidity sensor chamber(thum_bot)
• Top humidity(hum_top)
• bottom air temperature(tair_bot)
• top vapor pressure(vp_top)

• Temperature of left humidity sensor chamber(rr_thum_l)
• Temperature of right humidity sensor chamber(rr_thum_r)
• Right relative humidity(mv_hum_r)
• Left air temperature(tair_l)
• Left relative humidity(mv_hum_l)
• Right air temperature(tair_r)

SGP/EBBR/E20 - 6 Month Checks

Many measurements were incorrect while the AEM was positioned with both aspirators at the 
same height for comparison checks.

• Bottom humidity(hum_bot)
• Top humidity(hum_top)
• top vapor pressure(vp_top)
• bottom vapor pressure(vp_bot)
• Temperature of the top humidity chamber(thum_top)
• top air temperature(tair_top)
• Temperature of bottom humidity sensor chamber(thum_bot)
• ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
• latent heat flux(e)
• h(h)
• bottom air temperature(tair_bot)

• Left relative humidity(mv_hum_l)
• Temperature of left humidity sensor chamber(rr_thum_l)
• Temperature of right humidity sensor chamber(rr_thum_r)
• Left air temperature(tair_l)
• Right air temperature(tair_r)
• Right relative humidity(mv_hum_r)

• Temperature of the top humidity chamber(thum_top)
• bottom air temperature(tair_bot)
• Top humidity(hum_top)
• Bottom humidity(hum_bot)
• bottom vapor pressure(vp_bot)
• top air temperature(tair_top)
• Temperature of bottom humidity sensor chamber(thum_bot)
• top vapor pressure(vp_top)

SGP/EBBR/E26 - 6 Month Checks

Many measurements were incorrect while the AEM was positioned with both aspirators at the 
same height for comparison checks.

• Temperature of right humidity sensor chamber(rr_thum_r)
• Right air temperature(tair_r)
• Left air temperature(tair_l)
• Right relative humidity(mv_hum_r)
• Temperature of left humidity sensor chamber(rr_thum_l)
• Left relative humidity(mv_hum_l)

• bottom air temperature(tair_bot)
• Bottom humidity(hum_bot)
• Top humidity(hum_top)
• Temperature of the top humidity chamber(thum_top)
• bottom vapor pressure(vp_bot)
• top air temperature(tair_top)
• Temperature of bottom humidity sensor chamber(thum_bot)
• top vapor pressure(vp_top)

• top air temperature(tair_top)
• Temperature of bottom humidity sensor chamber(thum_bot)
• h(h)
• latent heat flux(e)
• top vapor pressure(vp_top)
• Bottom humidity(hum_bot)
• bottom vapor pressure(vp_bot)
• Top humidity(hum_top)
• bottom air temperature(tair_bot)
• ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
• Temperature of the top humidity chamber(thum_top)

SGP/EBBR/E27 - 6 Month Checks

Many measurements were incorrect while the AEM was positioned with both aspirators at the 
same height for comparison checks.

• Bottom humidity(hum_bot)
• Temperature of bottom humidity sensor chamber(thum_bot)
• top air temperature(tair_top)
• Top humidity(hum_top)
• bottom vapor pressure(vp_bot)
• top vapor pressure(vp_top)
• bottom air temperature(tair_bot)
• Temperature of the top humidity chamber(thum_top)

• Temperature of the top humidity chamber(thum_top)
• ratio of sensible/latent heat fluxes (Bowen ratio)(bowen)
• top air temperature(tair_top)
• latent heat flux(e)
• top vapor pressure(vp_top)
• Bottom humidity(hum_bot)
• bottom vapor pressure(vp_bot)
• bottom air temperature(tair_bot)
• h(h)
• Top humidity(hum_top)
• Temperature of bottom humidity sensor chamber(thum_bot)

• Right air temperature(tair_r)
• Temperature of right humidity sensor chamber(rr_thum_r)
• Left air temperature(tair_l)
• Left relative humidity(mv_hum_l)
• Right relative humidity(mv_hum_r)
• Temperature of left humidity sensor chamber(rr_thum_l)

SGP/EBBR/E27 - Soil Moisture #5 Incorrect

The wrong CR10 program loaded from the storage module on 9/15/04.  During the previous 
change of program, an attempt was made to store the new program in the storage module; site 
ops techs did not notice that this attempt failed, leaving the old program in the storage 
module.  When power was cyled on 9/15/04, the old program with flat sm5 coefficients 
loaded into the CR10.  The "flat" coefficients resulted in the sm5 soil moisture hovering 
around 30%.

15 minute raw sm5 resistances were correct.

Average soil heat flow, sensible heat flux, and latent heat flux were not
significantly affected and so are not included in the list of incorrect measurements.

• volumetric soil moisture, site 5(sm5)

SGP/EBBR/E19 - Reprocess: Negative Net Rad calibrations

The calibration for negative net radiation was incorrectly entered in the datalogger 
program.

• net radiation(q)

• h(h)
• latent heat flux(e)
• net radiation(q)

SGP/EBBR/E26 - Incorrect soil type coefficients used

The soil type coefficents for soil moisture were incorrect from the day
of the system installation on, making soil moisture values too large.

As a result, soil heat flows were overmeasured, and sensible and latent heat fluxes were 
underestimated.

• 5 cm soil heat flow corrected for soil moisture content, site 5(c_shf5)
• Soil heat capacity 1(cs1)
• soil heat flow, site 1(g1)
• Soil heat capacity 4(cs4)
• 0-5 cm change in soil heat storage with time, site 4(ces4)
• volumetric soil moisture, site 5(sm5)
• h(h)
• volumetric soil moisture, site 2(sm2)
• latent heat flux(e)
• 0-5 cm change in soil heat storage with time, site 5(ces5)
• soil heat flow, site 2(g2)
• volumetric soil moisture, site 3(sm3)
• 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
• 5 cm soil heat flow corrected for soil moisture content, site 1(c_shf1)
• Soil heat capacity 5(cs5)
• volumetric soil moisture, site 4(sm4)
• 0-5 cm change in soil heat storage with time, site 3(ces3)
• soil heat flow, site 5(g5)
• volumetric soil moisture, site 1(sm1)
• Soil heat capacity 3(cs3)
• Soil heat capacity 2(cs2)
• average surface soil heat flow(ave_shf)
• 5 cm soil heat flow corrected for soil moisture content, site 3(c_shf3)
• 0-5 cm change in soil heat storage with time, site 2(ces1)
• soil heat flow, site 3(g3)
• 5 cm soil heat flow corrected for soil moisture content, site 4(c_shf4)
• soil heat flow, site 4(g4)
• 0-5 cm change in soil heat storage with time, site 2(ces2)

SGP/EBBR/E27 - SM2 Coefficients Incorect

Soil Moisture #2 coefficients in the CR10 datalogger program were incorrect during the 
time
that an old program version was installed.

• 5 cm soil heat flow corrected for soil moisture content, site 2(c_shf2)
• volumetric soil moisture, site 2(sm2)
• Soil heat capacity 2(cs2)
• soil heat flow, site 2(g2)
• 0-5 cm change in soil heat storage with time, site 2(ces2)

• Soil moisture 2(r_sm2)

SGP/EBBR/E13 - Improved EBBR CR10 Program

Effective 20050331.2100, the EBBR.E13 CR10 program was revised to improve the quality of 
the primary measurements as follows:

1) An RMS procedure is used to determine max and min limits of acceptable soil heat flow.  
This is applied to the individual soil sets.  Measurements outside the limits are 
rejected and the measurements within the limits are used to calculate the average soil heat flow.

2) Max and min limits are used to determine incorrect values of net radiation, sensible 
heat flux (h), latent heat flux (e), and automatic exchange mechanism (AEM) signal.  If AEM 
signal is outside the limits, h and e are set to 999s.  If net radiation is outside the 
limits, h and e are set to 999s. If h or e are outside the limits, h and e are set to 999s.

Virtually no incorrect soil measurement will affect the primary measurements of h and e.

By setting h and e to 999s, it can be easily seen that the primary variables are 
incorrect; no other interpretation is possible.

Prior to 20050331, the improved CR10 program was NOT in effect.  DQRs have been submitted 
for known instances of incorrect soil measurements which affected the quality of the 
primary measurements of h and e.

Note: the DQR begin date is the begin date of the sgp30ebbrE13.b1 data stream.  The 
earlier version of the CR10 program was also used on previous EBBR datastream names (e.g. 
sgp30ebbrE13.a1).

• average surface soil heat flow(ave_shf)
• latent heat flux(e)
• h(h)

SGP/EBBR/E15 - Improved EBBR CR10 Program

Effective 20050329.1900, the EBBR.E15 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050329, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE15.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE15.a1).

• latent heat flux(e)
• average surface soil heat flow(ave_shf)
• h(h)

SGP/EBBR/E18 - Improved EBBR CR10 Program

Effective 20050330.0000, the EBBR.E18 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050330, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE18.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE18.a1).

• latent heat flux(e)
• h(h)
• average surface soil heat flow(ave_shf)

SGP/EBBR/E19 - Improved EBBR CR10 Program

Effective 20050331.1600, the EBBR.E19 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050331, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE19.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE19.a1).

• average surface soil heat flow(ave_shf)
• h(h)
• latent heat flux(e)

SGP/EBBR/E20 - Improved EBBR CR10 Program

Effective 20050330.1900, the EBBR.E20 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050330, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE20.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE20.a1).

• average surface soil heat flow(ave_shf)
• latent heat flux(e)
• h(h)

SGP/EBBR/E22 - Improved EBBR CR10 Program

Effective 20050330.1930, the EBBR.E20 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050330, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE20.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE20.a1).

• h(h)
• average surface soil heat flow(ave_shf)
• latent heat flux(e)

SGP/EBBR/E26 - Improved EBBR CR10 Program

Effective 20050331.1700, the EBBR.E26 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050331, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE26.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE26.a1).
~

• latent heat flux(e)
• h(h)
• average surface soil heat flow(ave_shf)

SGP/EBBR/E27 - Improved EBBR CR10 Program

Effective 20050330.1730, the EBBR.E27 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050330, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE27.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE27.a1).

• average surface soil heat flow(ave_shf)
• h(h)
• latent heat flux(e)

SGP/EBBR/E2 - Improved EBBR CR10 Program

Effective 20050324.1700, the EBBR.E2 CR10 program was revised to improve the quality of 
the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h and e are set to 
999s.  If net radiation is outside the limits, h and e are set to 999s. If h or e are 
outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary variables are 
incorrect; no other interpretation is possible.
   
Prior to 20050324, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE2.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE2.a1).

• average surface soil heat flow(ave_shf)
• h(h)
• latent heat flux(e)

SGP/EBBR/E4 - Improved EBBR CR10 Program

Effective 20050323.1800, the EBBR.E4 CR10 program was revised to improve the quality of 
the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h and e are set to 
999s.  If net radiation is outside the limits, h and e are set to 999s. If h or e are 
outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary variables are 
incorrect; no other interpretation is possible.
   
Prior to 20050323, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE4.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE4.a1).

• h(h)
• average surface soil heat flow(ave_shf)
• latent heat flux(e)

SGP/EBBR/E7 - Improved EBBR CR10 Program

Effective 20050322.1900, the EBBR.E7 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050322, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE7.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE7.a1).

• average surface soil heat flow(ave_shf)
• h(h)
• latent heat flux(e)

SGP/EBBR/E8 - Improved EBBR CR10 Program

Effective 20050322.1730, the EBBR.E8 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050322, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE8.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE8.a1).

• average surface soil heat flow(ave_shf)
• latent heat flux(e)
• h(h)

SGP/EBBR/E9 - Improved EBBR CR10 Program

Effective 20050322.1600, the EBBR.E9 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050322, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE9.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE9.a1).

• latent heat flux(e)
• average surface soil heat flow(ave_shf)
• h(h)

SGP/EBBR/E12 - Improved EBBR CR10 Program

Effective 20050329.1830, the EBBR.E12 CR10 program was revised to improve 
the quality of the primary measurements as follows:
   
1) An RMS procedure is used to determine max and min limits of acceptable
soil heat flow.  This is applied to the individual soil sets.  Measurements
outside the limits are rejected and the measurements within the limits are
used to calculate the average soil heat flow.
   
2) Max and min limits are used to determine incorrect values of net
radiation, sensible heat flux (h), latent heat flux (e), and automatic
exchange mechanism (AEM) signal.  If AEM signal is outside the limits, h 
and e are set to 999s.  If net radiation is outside the limits, h and e are 
set to 999s. If h or e are outside the limits, h and e are set to 999s.
   
Virtually no incorrect soil measurement will affect the primary 
measurements of h and e.
   
By setting h and e to 999s, it can be easily seen that the primary 
variables are incorrect; no other interpretation is possible.
   
Prior to 20050329, the improved CR10 program was NOT in effect.  DQRs have
been submitted for known instances of incorrect soil measurements which
affected the quality of the primary measurements of h and e.
   
Note: the DQR begin date is the begin date of the sgp30ebbrE12.b1 data
stream.  The earlier version of the CR10 program was also used on previous
EBBR datastream names (e.g. sgp30ebbrE12.a1).

• latent heat flux(e)
• average surface soil heat flow(ave_shf)
• h(h)

SGP/EBBR/E12 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E12 data collected by ARM back to the installation of the 
instrument in August 1993. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.  

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil type
4) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E13 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E13 data collected by ARM back to the installation of the 
instrument in September 1992.  Please see the current metadata for correct information.  
These changes do not affect data values or quality.

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for systems
3) Correction of soil type
4) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E15 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E15 data collected by ARM back to the installation of the 
instrument in September 1992. Please see the current metadata for correct information.  
These changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil type
4) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E18 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E18 data collected by ARM back to the installation of the 
instrument in July 1997. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil type
4) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E19 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E19 data collected by ARM back to the beginning of the data 
set in May 1997. Please see the current metadata for correct information.  These changes 
do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil type
4) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E27 - metadata corrections

On 20050816, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E27 data collected by ARM back to the installation of the 
instrument in May 2003. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E2 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E2 data collected by ARM back to the installation of the 
instrument in May 1997. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E4 - metadata corrections

On 20050817, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E4 data collected by ARM back to the installation of the 
instrument in April 1993. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E7 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E7 data collected by ARM back to the installation of the 
instrument in May 1993. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E8 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E8 data collected by ARM back to the installation of the 
instrument in December 1992. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E9 - metadata corrections

On 20050420, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E9 data collected by ARM back to the installation of the 
instrument in December 1992. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E20 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E20 data collected by ARM back to the installation of the 
instrument in April 1993. Please see the current metadata for correct information.  These 
changes do not
affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E22 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E22 data collected by ARM back to the installation of the 
instrument in April 1993. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil type
4) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)

SGP/EBBR/E26 - metadata corrections

On 20050723, a series of metadata corrections and additions were completed.  These 
metadata changes apply to all EBBR.E26 data collected by ARM back to the installation of the 
instrument in June 1992. Please see the current metadata for correct information.  These 
changes do not affect data values or quality.	

The changes are summarized below:
1) Update of "sensor location" information
2) Addition of installation dates for the systems
3) Correction of soil moisture units (from "by volume" to "gravimetric")

• base time(base_time)

• base time(base_time)

• base time(base_time)