TWP/SMET/C3 - ORG data noisy due to degraded ground

SMET Rain Data began to be noisy during December 2005 and the problem slowly became worse 
over time so that in February 2006 the ORG was reporting with a constant background value 
of around 0.10 mm/hr rain rate.  ORG voltage showed a near constant value above the 85mV 
threshold.  The ground for the ORG had become degraded and was lost due to corrosion.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - Reprocessed: Lower windspeed sensor calibration error

The lower anemometer was replaced but the calibration coefficients were not changed during 
this period.  The data were reprocessed to apply the correct calibrations and the 
reprocessed data were archived in August 2008.

• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #2 speed standard deviation(wind2_spd_sd)

TWP/SMET/C3 - Anemometer Readings Incorrect

The Anemometer readings were incorrect due to the tower being lowered for maintenance.

• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #2 direction vector average(wind2_dir_vec_avg)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Wind #2 direction standard deviation(wind2_dir_sd)
• Wind #2 speed standard deviation(wind2_spd_sd)

TWP/SMET/C3 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the SMET suite of instruments effective 20060926. 
 Two new variables (count and rain amount) were added at the end of the twpsmet60sC1.b1 
datastream.  When reprocessing of this datastream occurs these variables will be added 
with -9999 (missing) as the value for dates prior to gauge installation.

• base time(base_time)

TWP/SMET/C3 - Barometer Data Incorrect

The barometer data was incorrect or missing due to water intrusion.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Data Incorrect Due to Water Intrusion

Data became erratic and unreasonable after water intrusion into the enclosure.

• Vapor pressure standard deviation(vappress_sd)
• Precipitation maximum(precip_max)
• Relative humidity maximum(relh_max)
• Mean Relative Humidity(relh_mean)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Relative humidity minimum(relh_min)
• precipitation minimum(precip_min)
• Precipitation mean(precip_mean)
• Temperature minimum(temp_min)
• Mean Air Temperature or Hardware Error(temp_mean)
• Temperature maximum(temp_max)
• Precipitation standard deviation(precip_sd)
• Vapor pressure mean(vappress_mean)
• Std Dev of Air Temperature(temp_sd)

TWP/SMET/C3 - Upper wind speed artificially slow

The upper wind measurement was consistently slower by around 0.5 - 1 m/s than the lower 
wind measurement.  The bearings on the upper wind measurement were binding.

• Wind #1 speed minimum(wind1_spd_min)
• Wind #1 speed maximum(wind1_spd_max)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Wind #1 speed vector average(wind1_spd_vec_avg)

TWP/SMET/C3 - ORG overestimated rainfall

Optical rain gauge (ORG) measured approximately 10mm higher than two co-located tipping 
bucket rain gauges and a co-located disdrometer.  The ORG is typically higher but usually 
not by an order of magnitude.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)