TWP/MET/C3 - WIND DIRECTION SENSOR #2 MISALIGNED

Wind direction sensor #2 was misaligned and off by 15 degrees.

• Wind #2 direction vector average(wind2_dir_vec_avg)
• Wind #2 direction standard deviation(wind2_dir_sd)

• Wind #2 direction standard deviation(wind2_dir_sd)
• Wind #2 direction vector average(wind2_dir_vec_avg)

TWP/SMET/C3 - Intermittent Pressure Sensor Failure

The Barometric Pressure sensor was intermittently failing at TWP site C3 Darwin.  At times 
there were large pressure fluctuations occurring on the order of 24 mb in a few minutes. 
 Times of large pressure fluctuations are readily apparent in the data.  At these times 
the data should be carefully analyzed before determining it's usefulness.  In between the 
periods of large fluctuations the readings appear to be stable.  It is still suggested 
that independent pressure data be obtained for comparison before use.

• Barometric Pressure(atmos_pressure)

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Data reported at 15sec rather than 60s intervals

Data in these data streams should be reports at 60sec intervals, but
the logger program running during this time had the interval set to
15s.  Users will have to average the 15sec data to get 60sec data.

• Vapor pressure mean(vappress_mean)
• External voltage(external_voltage)
• Temperature minimum(temp_min)
• Precipitation standard deviation(precip_sd)
• base time(base_time)
• Precipitation mean(precip_mean)
• Barometric Pressure(atmos_pressure)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #2 speed standard deviation(wind2_spd_sd)
• Wind #1 speed minimum(wind1_spd_min)
• lat(lat)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Dummy altitude for Zeb(alt)
• Logger panel temperature(logger_temp)
• Std Dev of Air Temperature(temp_sd)
• Vapor pressure standard deviation(vappress_sd)
• Relative humidity maximum(relh_max)
• Mean Air Temperature or Hardware Error(temp_mean)
• lon(lon)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Mean Relative Humidity(relh_mean)
• Time offset of tweaks from base_time(time_offset)
• Relative humidity minimum(relh_min)
• Wind #2 direction standard deviation(wind2_dir_sd)
• Bit data. See details.(bit_data)
• Wind #2 direction vector average(wind2_dir_vec_avg)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Wind #2 speed minimum(wind2_spd_min)
• Battery Voltage(internal_voltage)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Temperature maximum(temp_max)
• precipitation minimum(precip_min)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• Wind #1 speed maximum(wind1_spd_max)
• Precipitation maximum(precip_max)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #2 speed maximum gust(wind2_spd_max_gust)

• Time offset of tweaks from base_time(time_offset)
• Precipitation maximum(precip_max)
• Battery Voltage(internal_voltage)
• Wind #1 speed minimum(wind1_spd_min)
• Wind #2 speed maximum(wind2_spd_max)
• Wind #1 direction standard deviation(wind1_dir_sd)
• Wind #2 speed minimum(wind2_spd_min)
• Wind #1 speed maximum(wind1_spd_max)
• Mean Air Temperature or Hardware Error(temp_mean)
• Temperature maximum(temp_max)
• Barometric Pressure(atmos_pressure)
• Relative humidity maximum(relh_max)
• Mean Relative Humidity(relh_mean)
• Wind #1 direction vector average(wind1_dir_vec_avg)
• Wind #1 speed standard deviation(wind1_spd_sd)
• Std Dev of Relative Humidity or Hardware Error Code(relh_sd)
• Relative humidity minimum(relh_min)
• Bit data. See details.(bit_data)
• Temperature minimum(temp_min)
• Dummy altitude for Zeb(alt)
• Wind #2 speed maximum gust(wind2_spd_max_gust)
• Precipitation standard deviation(precip_sd)
• Wind #1 speed maximum gust(wind1_spd_max_gust)
• lon(lon)
• Wind #2 direction standard deviation(wind2_dir_sd)
• Wind #2 speed standard deviation(wind2_spd_sd)
• External voltage(external_voltage)
• lat(lat)
• Wind #2 speed arithmetic average(wind2_spd_arith_avg)
• Logger panel temperature(logger_temp)
• precipitation minimum(precip_min)
• Vapor pressure mean(vappress_mean)
• Vapor pressure standard deviation(vappress_sd)
• Wind #1 speed vector average(wind1_spd_vec_avg)
• Wind #2 direction vector average(wind2_dir_vec_avg)
• Precipitation mean(precip_mean)
• Wind #2 speed vector average(wind2_spd_vec_avg)
• base time(base_time)
• Wind #1 speed arithmetic average(wind1_spd_arith_avg)
• Std Dev of Air Temperature(temp_sd)

TWP/SMET/C3 - Rain blocked pressure port

Atmospheric pressure values were suspect due to anomolous readings during heavy rain 
events.  Suspect blockage of port due to rainfall.  New logger and enclosure corrected problem.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Negative rainfall rates

Due to limitations of the Zeno dataloggers all voltage measurements
from the optical rain gauge (ORG) were converted to rainfall rates. 
This resulted in negative values for rain rates.  Any value below
0.10 mm/hr should be considered to be 0 mm/hr.  New dataloggers 
alleviated this problem.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - Instrument failure

A lightning strike caused a failure in the ORG.  Rainfall was being continually recorded.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - ORG data noisy due to degraded ground

SMET Rain Data began to be noisy during December 2005 and the problem slowly became worse 
over time so that in February 2006 the ORG was reporting with a constant background value 
of around 0.10 mm/hr rain rate.  ORG voltage showed a near constant value above the 85mV 
threshold.  The ground for the ORG had become degraded and was lost due to corrosion.

• Precipitation mean(precip_mean)
• Precipitation maximum(precip_max)
• Precipitation standard deviation(precip_sd)
• precipitation minimum(precip_min)

TWP/SMET/C3 - Reprocess: Barometric Data Changed from hPa to kPa

Barometric pressure data was converted from hPa to kPa in order to standardize the 
measurement units among ARM sites and to conform to accepted standard units determined by the 
scientific community.

• Barometric Pressure(atmos_pressure)

TWP/SMET/C3 - Reprocess: Tipping bucket rain gauge added

A tipping bucket rain gauge was added to the SMET suite of instruments effective 20060926. 
 Two new variables (count and rain amount) were added at the end of the twpsmet60sC1.b1 
datastream.  When reprocessing of this datastream occurs these variables will be added 
with -9999 (missing) as the value for dates prior to gauge installation.

• base time(base_time)