TWP/MWR/C2 - Excessive wet_window flags

The wet_window flag is set high more than expected from the measured value of liquid water 
path. This may be caused by dew or, if the heater sensivity is slightly misadjusted, by 
the diurnal variation in ambient temperature.

The "wet_window" flag is an indicator of moisture on the MWR window which invalidates the 
measurements of precipitable water vapor and liquid water path. Sometimes this flag can 
be incorrectly set high or low if the heater sensivity is slightly misadjusted. The heater 
adjustment is a resistive device that is dependent on ambient temperature. Another 
indicator of moisture on the window is unreasonably high ( > 3*liquid_retrieval_rms_accuracy ) 
values of "liq".

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

TWP/MWR/C3 - Elevated Skybrightness Temperatures

For an unknown reason, the MWR began to exhibit elevated sky brightness 
temperatures. This problem was corrected when the instrument was power-cycled.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)

TWP/MWR/C3 - Wet Window Flag not correct

The moisture sensor threshold voltage in the MWR configuration file was 
set to the wrong value for the new heater/blower assembly. This caused the 
wet window flag to not be set high during times of rain.

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

TWP/MWR/C3 - Intermittent Negative Sky Brightness Temperatures

Several related and recurring problems with the MWRs have been reported
dating back to 1999.  These problems were due to the occurrence of
blackbody signals (in counts) that were half of those expected. The
symptoms included noisy data, spikes in the data, negative brightness
temperatures, and apparent loss of serial communication between the
computer and the radiometer, which results in a self-termination of the
MWR program.

Because these all initially appeared to be hardware-related problems,
the instrument mentor and SGP site operations personnel (1) repeatedly
cleaned and replaced the fiber optic comm. components, (2) swapped
radiometers, (3) sent radiometers back to Radiometrics for evaluation
(which did not revealed any instrument problems), and (4) reconfigured
the computer's operating system.  Despite several attempts to isolate
and correct it, the problem persisted.

It became apparent that some component of the Windows98 configuration
conflicted with the DOS-based MWR program or affected the serial port
or the contents of the serial port buffer. This problem was finally
corrected by upgrading the MWR software with a new Windows-compatible
program.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)

TWP/MWR/C1 - Intermittent Negative Sky Brightness Temperatures

Several related and recurring problems with the MWRs have been reported dating back to 
1999.  These problems were due to the occurrence of blackbody signals (in counts) that were 
half of those expected. The symptoms included noisy data, spikes in the data, negative 
brightness temperatures, and apparent loss of serial communication between the computer and 
the radiometer, which results in a self-termination of the MWR program.

Because these all initially appeared to be hardware-related problems, the instrument 
mentor and SGP site operations personnel (1) repeatedly cleaned and replaced the fiber optic 
comm. components, (2) swapped radiometers, (3) sent radiometers back to Radiometrics for 
evaluation (which did not revealed any instrument problems), and (4) reconfigured the 
computer's operating system.  Despite several attempts to isolate and correct it, the problem 
persisted.

It became apparent that some component of the Windows98 configuration conflicted with the 
DOS-based MWR program or affected the serial port or the contents of the serial port 
buffer. This problem was finally corrected by upgrading the MWR software with a new 
Windows-compatible program.

• MWR column precipitable water vapor(vap)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Averaged total liquid water along LOS path(liq)

TWP/MWR/C3 - min/max/delta values incorrect

The values of valid_min, valid_max, and valid_delta for fields tkxc and tknd were 
incorrect. They should be 303, 333, and 0.5 K, respectively.

• Mixer kinetic (physical) temperature(tkxc)
• (tknd)

TWP/MWR/C2 - thermal instability

The MWR required an unusually long time to reach thermal stability after a 4-day outage 
due to a power failure that damaged the blower/heater assembly. Also during this period, 
the heater, which had been replaced, appears to have been on continously, causing the data 
to be inappropriately flagged.

• 31.4 GHz sky signal(sky31)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• MWR column precipitable water vapor(vap)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)

• 31.4 GHz sky signal(tipsky31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 23.8 GHz sky signal(tipsky23)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Temperature correction coefficient at 31.4 GHz(tc31)

TWP/MWR/C1 - wrong azimuth

The MWR was initially installed at an azimuth angle defined as 180 degrees but the value 
in the configuration file was not changed from the default of 0 degrees. In examining 
photos taken during the installation of the AWS tower, I noticed that the MWR was rotated 
opposite the normal orientation. The value in the configuration file was changed to reflect 
the actual azimuth of the instrument.

• Actual Azimuth(actaz)

TWP/MWR/C2 - Data collection problem

Large, frequent data gaps occurred due to a failing laptop computer. The problem was 
corrected when a new computer was installed.

• 31.4 GHz sky signal(sky31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Mixer kinetic (physical) temperature(tkxc)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Blackbody kinetic temperature(tkbb)
• lat(lat)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• 31.4 GHz blackbody(bb31)
• MWR column precipitable water vapor(vap)
• 23.8 GHz sky signal(sky23)
• Ambient temperature(tkair)
• IR Brightness Temperature(ir_temp)
• base time(base_time)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• lon(lon)
• 23.8 GHz Blackbody signal(bb23)
• (tknd)
• Actual Azimuth(actaz)
• Time offset of tweaks from base_time(time_offset)
• Actual elevation angle(actel)
• Dummy altitude for Zeb(alt)
• Sky Infra-Red Temperature(sky_ir_temp)
• Temperature correction coefficient at 31.4 GHz(tc31)

• Raw data stream - documentation not supported(Raw data stream - documentation not supported)

• 31.4 GHz sky signal(tipsky31)
• lat(lat)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.4 GHz goodness-of-fit coefficient(r31)
• Actual Azimuth(actaz)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 31.4 GHz blackbody(bb31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Ambient temperature(tkair)
• Dummy altitude for Zeb(alt)
• (tknd)
• base time(base_time)
• Blackbody kinetic temperature(tkbb)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Time offset of tweaks from base_time(time_offset)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Actual elevation angle(actel)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• lon(lon)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 31.4 GHz(tc31)

TWP/MWR/C2 - Heater problem

When the wiring of the air temperature sensor was checked the heater apparently began 
activating too often.

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

• Fraction of data in averaging interval with water on Teflon window(water_flag_fraction)

• Water on Teflon window (1=WET, 0=DRY)(wet_window)

TWP/MWR/C2 - mixer temperature

When the wiring of the air temperature sensor was checked the mixer temperature 
unexpectedly decreased 4 degrees. It increased to its normal value when the dielectric window was 
replaced. The problem was probably caused by a loose and/or corroded connection.

• Mixer kinetic (physical) temperature(tkxc)

• Mixer kinetic (physical) temperature(tkxc)

TWP/MWR/C2 - Reprocessed: Revised Retrieval Coefficients

IN THE BEGINNING (June 1992), the retrieval coefficients used to derive the precipitable 
water vapor (PWV) and liquid water path (LWP) from the MWR brightness temperatures were 
based on the Liebe and Layton (1987) water vapor and oxygen absorption model and the Grant 
(1957) liquid water absorption model.

Following the SHEBA experience, revised retrievals based on the more recent Rosenkranz 
(1998) water vapor and oxygen absorption models and the Liebe (1991) liquid waer absorption 
model were developed.  The Rosenkranz water vapor absorption model resulted a 2 percent 
increase in PWV relative to the earlier Liebe and Layton model.  The Liebe liquid water 
absorption model decreased the LWP by 10% relative to the Grant model.  However, the 
increased oxygen absorption caused a 0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was 
particularly significant for low LWP conditions (i.e. thin clouds encountered at SHEBA).

Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and Clough, TGARS v. 43, 
pp 1102-1108, 2005) that the half-width of the 22 GHz water vapor line from the HITRAN 
compilation, which is 5 percent smaller than the Liebe and Dillon (1969) half-width used in 
Rosenkranz (1998), provided a better fit to the microwave brightness temperature 
measurements at 5 frequencies in the range 22-30 GHz, and yielded more accurate retrievals. 
Accordingly, revised MWR retrieval coefficients have been developed using MONORTM, which 
utilizes the HITRAN compilation for its spectroscopic parameters.  These new retrievals 
provide 3 percent less PWV and 2.6 percent greater LWP than the previous 
retrievals based on Rosenkranz (1998).

The Rosenkranz-based retrieval coefficients became active at TWP.C2 20020427.0600.  The 
MONORTM-based retrieval coefficients became active at TWP.C2 20050630.2100.

Note: The TWP.C2 data for 19981028-20050630 have been reprocessed to apply the 
MONORTM-based retrievals for all time.  The reprocessed data were archived 20061003.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Ensemble average for MWR liquid in window centered about balloon release(mean_liq_mwr)
• Ensemble average for MWR vapor in window centered about balloon release(mean_vap_mwr)

• Averaged total liquid water along LOS path(liq)
• MWR column precipitable water vapor(vap)

TWP/MWR/C3 - Reprocess - Revised Retrieval Coefficients

IN THE BEGINNING (June 1992), the retrieval coefficients used to derive 
the precipitable water vapor (PWV) and liquid water path (LWP) from the 
MWR brightness temperatures were based on the Liebe and Layton (1987) 
water vapor and oxygen absorption model and the Grant (1957) liquid 
water absorption model.

Following the SHEBA experience, revised retrievals based on the more 
recent Rosenkranz (1998) water vapor and oxygen absorption models and 
the Liebe (1991) liquid waer absorption model were developed.  The 
Rosenkranz water vapor absorption model resulted a 2 percent increase 
in PWV relative to the earlier Liebe and Layton model.  The Liebe 
liquid water absorption model decreased the LWP by 10% relative to the 
Grant model.  However, the increased oxygen absorption caused a 
0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was particularly 
significant for low LWP conditions (i.e. thin clouds encountered at 
SHEBA).

Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and 
Clough, TGARS v. 43, pp 1102-1108, 2005) that the half-width of the 
22 GHz water vapor line from the HITRAN compilation, which is 5 percent 
smaller than the Liebe and Dillon (1969) half-width used in Rosenkranz 
(1998), provided a better fit to the microwave brightness temperature 
measurements at 5 frequencies in the range 22-30 GHz, and yielded more 
accurate retrievals. Accordingly, revised MWR retrieval coefficients 
have been developed using MONORTM, which utilizes the HITRAN compilation 
for its spectroscopic parameters.  These new retrievals provide 3 
percent less PWV and 2.6 percent greater LWP than the previous 
retrievals based on Rosenkranz (1998).

Although the MWR data will be reprocessed to apply the new monortm-based 
retrievals, for most purposes it will be sufficient to correct the data 
using the following factors:

PWV_MONORTM = 0.9695 * PWV_ROSENKRANZ
LWP_MONORTM = 1.026  * LWP_ROSENKRANZ

The Rosenkranz-based retrieval coefficients was active at TWP.C3 from
inception of the data, 20020227.0151.  The MONORTM-based retrieval
coefficients became active at TWP.C3 20050630.2100.

Note: a reprocessing effort is already underway to apply the 
Rosenkranz-based retrieval coefficients to all MWR prior to April 
2002.  An additional reprocessing task will be undertaken to apply 
the MONORTM retrieval to all MWR data when the first is completed. 
Read reprocessing comments in the netcdf file header carefully to 
ensure you are aware which retrieval is in play.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)

TWP/MWR/C1 - Reprocessed: Revised Retrieval Coefficients

IN THE BEGINNING (June 1992), the retrieval coefficients used to derive 
the precipitable water vapor (PWV) and liquid water path (LWP) from the 
MWR brightness temperatures were based on the Liebe and Layton (1987) 
water vapor and oxygen absorption model and the Grant (1957) liquid 
water absorption model.

Following the SHEBA experience, revised retrievals based on the more 
recent Rosenkranz (1998) water vapor and oxygen absorption models and 
the Liebe (1991) liquid waer absorption model were developed.  The 
Rosenkranz water vapor absorption model resulted a 2 percent increase 
in PWV relative to the earlier Liebe and Layton model.  The Liebe 
liquid water absorption model decreased the LWP by 10% relative to the 
Grant model.  However, the increased oxygen absorption caused a 
0.02-0.03 mm (20-30 g/m2) reduction in LWP, which was particularly 
significant for low LWP conditions (i.e. thin clouds encountered at 
SHEBA).

Recently, it has been shown (Liljegren, Boukabara, Cady-Pereira, and 
Clough, TGARS v. 43, pp 1102-1108, 2005) that the half-width of the 
22 GHz water vapor line from the HITRAN compilation, which is 5 percent 
smaller than the Liebe and Dillon (1969) half-width used in Rosenkranz 
(1998), provided a better fit to the microwave brightness temperature 
measurements at 5 frequencies in the range 22-30 GHz, and yielded more 
accurate retrievals. Accordingly, revised MWR retrieval coefficients 
have been developed using MONORTM, which utilizes the HITRAN compilation 
for its spectroscopic parameters.  These new retrievals provide 3 
percent less PWV and 2.6 percent greater LWP than the previous 
retrievals based on Rosenkranz (1998).

The Rosenkranz-based retrieval coefficients became active at TWP.C1 
20020504.0200.  The MONORTM-based retrieval coefficients became active 
at TWP.C1 20050630.2100.

Note: The TWP.C1 data for 19961011-20050630 have been reprocessed to apply the

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)

TWP/MWR/C1 - New software version (4.15) installed

A problem began with the installation of MWR.EXE version 4.12 in October 2002. The 
software had been upgraded from a "DOS" to a "Windows"-compiled program to address an earlier 
problem.  The software upgrade corrected the earlier problem but introduced a new one that 
caused line-of-sight observing cycles to be skipped, a 15% reduction in the number of tip 
curves, and saturation of CPU usage.  Software versions 4.13 and 4.14 also produced 
these problems.

The new MWR software version (4.15) was installed on 9/13/2005. As a consequence of this 
upgrade, the tip curve frequency increased. The tip cycle time decreased from ~60s to ~50s.

• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 23.8 GHz(tc23)
• IR Brightness Temperature(ir_temp)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• 23.8 GHz Blackbody signal(bb23)
• Blackbody kinetic temperature(tkbb)
• (tknd)
• 31.4 GHz blackbody(bb31)
• 31.4 GHz sky signal(sky31)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Temperature correction coefficient at 31.4 GHz(tc31)
• MWR column precipitable water vapor(vap)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Ambient temperature(tkair)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Sky Infra-Red Temperature(sky_ir_temp)
• 23.8 GHz sky signal(sky23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)

• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Tip configuration number(tipn)
• Mixer kinetic (physical) temperature(tkxc)
• IR Brightness Temperature(ir_temp)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz Blackbody signal(bb23)
• Ambient temperature(tkair)
• (tknd)
• 31.4 GHz goodness-of-fit coefficient(r31)
• Blackbody kinetic temperature(tkbb)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 23.8 GHz sky signal(tipsky23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 31.4 GHz blackbody(bb31)
• Blackbody temperature 1(tkbb1)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• Blackbody temperature 2(tkbb2)
• Temperature correction coefficient at 31.4 GHz(tc31)

TWP/MWR/C2 - New software version (4.15) installed

A problem began with the installation of MWR.EXE version 4.12 in November 2002. The 
software had been upgraded from a "DOS" to a "Windows"-compiled program to address an earlier 
problem.  The software upgrade corrected the earlier problem but introduced a new one that 
caused line-of-sight observing cycles to be skipped, a 15% reduction in the number of 
tip curves, and saturation of CPU usage.  Software versions 4.13 and 4.14 also produced 
these problems.

The new MWR software version (4.15) was installed on 9/15/2005. As a consequence of this 
upgrade, the tip curve frequency increased. The tip cycle time decreased from ~60s to ~50s.

• 31.4 GHz sky signal(sky31)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Mixer kinetic (physical) temperature(tkxc)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Blackbody kinetic temperature(tkbb)
• 23.8 GHz Blackbody signal(bb23)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• 31.4 GHz blackbody(bb31)
• MWR column precipitable water vapor(vap)
• 23.8 GHz sky signal(sky23)
• (tknd)
• Ambient temperature(tkair)
• IR Brightness Temperature(ir_temp)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Sky Infra-Red Temperature(sky_ir_temp)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)

• 31.4 GHz sky signal(tipsky31)
• (tknd)
• Blackbody kinetic temperature(tkbb)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 31.4 GHz blackbody(bb31)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Mixer kinetic (physical) temperature(tkxc)
• Ambient temperature(tkair)

TWP/MWR/C3 - New software version (4.15) installed

A problem began with the installation of MWR.EXE version 4.12 in October 2002. The 
software had been upgraded from a "DOS" to a "Windows"-compiled program to address an earlier 
problem.  The software upgrade corrected the earlier problem but introduced a new one that 
caused line-of-sight observing cycles to be skipped, a 15% reduction in the number of tip 
curves, and saturation of CPU usage.  Software versions 4.13 and 4.14 also produced 
these problems.

The new MWR software version (4.15) was installed on 9/20/2005. As a consequence of this 
upgrade, the tip curve frequency increased. The tip cycle time decreased from ~60s to ~50s.

• Sky brightness temperature at 31.4 GHz(tbsky31)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz Blackbody signal(bb23)
• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)
• 31.4 GHz blackbody(bb31)
• 31.4 GHz sky signal(sky31)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Sky Infra-Red Temperature(sky_ir_temp)
• Blackbody kinetic temperature(tkbb)
• Mixer kinetic (physical) temperature(tkxc)
• (tknd)
• Ambient temperature(tkair)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)

• Ambient temperature(tkair)
• Blackbody kinetic temperature(tkbb)
• (tknd)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz sky signal(tipsky23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 31.4 GHz blackbody(bb31)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Mixer kinetic (physical) temperature(tkxc)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 23.8 GHz Blackbody signal(bb23)

TWP/MWR/C3 - Instrument failure, Power outage

A lightning strike sent the MWR offline. The radiometer suffered extensive damage, was 
removed from the site and sent to the vendor for repair. A spare radiometer was sent to the 
TWP/C3 site and was installed on 12/07. However, some hardaware communication issues 
prevented data collection until 12/10.

• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• MWR column precipitable water vapor(vap)
• 23.8 GHz Blackbody signal(bb23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• base time(base_time)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 23.8 GHz(tc23)
• (tknd)
• Averaged total liquid water along LOS path(liq)
• Dummy altitude for Zeb(alt)
• 31.4 GHz blackbody(bb31)
• lon(lon)
• Ambient temperature(tkair)
• Sky Infra-Red Temperature(sky_ir_temp)
• 23.8 GHz sky signal(sky23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• lat(lat)
• Time offset of tweaks from base_time(time_offset)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Blackbody kinetic temperature(tkbb)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 31.4 GHz sky signal(sky31)

• 23.8 GHz blackbody+noise injection signal(bbn23)
• lon(lon)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Time offset of tweaks from base_time(time_offset)
• MWR column precipitable water vapor(vap)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• (tknd)
• Ambient temperature(tkair)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• base time(base_time)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Dummy altitude for Zeb(alt)
• 23.8 GHz Blackbody signal(bb23)
• Averaged total liquid water along LOS path(liq)
• 31.4 GHz blackbody(bb31)
• 31.4 GHz sky signal(sky31)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• lat(lat)
• Sky Infra-Red Temperature(sky_ir_temp)
• Blackbody kinetic temperature(tkbb)
• Mixer kinetic (physical) temperature(tkxc)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)

• Ambient temperature(tkair)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz blackbody(bb31)
• Time offset of tweaks from base_time(time_offset)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• base time(base_time)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 23.8 GHz Blackbody signal(bb23)
• Blackbody kinetic temperature(tkbb)
• (tknd)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• lon(lon)
• Mixer kinetic (physical) temperature(tkxc)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Dummy altitude for Zeb(alt)
• lat(lat)
• Actual elevation angle(actel)
• Actual Azimuth(actaz)

• Raw data stream - documentation not supported(Raw data stream - documentation not supported)

TWP/MWR/C3 - REPROCESS- Updated retrieval coefficients

The statistical retrieval coefficients currently in use at the Darwin (TWP/C3) site were 
developed using radiosonde RS80 launched from Manus Island during the TOGA-COARE 
experiment.
Data from Manus Island have minimal seasonality, therefore a single, annual set of 
coefficients was used at all three sites. Retrievals using these coefficients are sufficiently 
accurate especially during the local summer months (December-January). However, the Darwin 
site displays a summer/winter seasonality resulting in larger differences during the 
southern winter (May-
June).
Since we now have enough radiosonde soundings (RS80 and RS90) available at the Darwin 
site, the Darwin coefficients were modified to better reflect the local seasonality.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)

• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)

TWP/MWR/C3 - Site shutdown

On 4/24, the site was shutdown in preparation for a cyclone. Instruments were back up on 
4/25 at 22:59

• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• MWR column precipitable water vapor(vap)
• 23.8 GHz Blackbody signal(bb23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• base time(base_time)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 23.8 GHz(tc23)
• (tknd)
• Averaged total liquid water along LOS path(liq)
• Dummy altitude for Zeb(alt)
• 31.4 GHz blackbody(bb31)
• lon(lon)
• Ambient temperature(tkair)
• Sky Infra-Red Temperature(sky_ir_temp)
• 23.8 GHz sky signal(sky23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• lat(lat)
• Time offset of tweaks from base_time(time_offset)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Blackbody kinetic temperature(tkbb)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 31.4 GHz sky signal(sky31)

• 23.8 GHz blackbody+noise injection signal(bbn23)
• lon(lon)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Time offset of tweaks from base_time(time_offset)
• MWR column precipitable water vapor(vap)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• (tknd)
• Ambient temperature(tkair)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• base time(base_time)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Dummy altitude for Zeb(alt)
• 23.8 GHz Blackbody signal(bb23)
• Averaged total liquid water along LOS path(liq)
• 31.4 GHz blackbody(bb31)
• 31.4 GHz sky signal(sky31)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• lat(lat)
• Sky Infra-Red Temperature(sky_ir_temp)
• Blackbody kinetic temperature(tkbb)
• Mixer kinetic (physical) temperature(tkxc)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)

• Ambient temperature(tkair)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz blackbody(bb31)
• Time offset of tweaks from base_time(time_offset)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• base time(base_time)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 23.8 GHz Blackbody signal(bb23)
• Blackbody kinetic temperature(tkbb)
• (tknd)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• lon(lon)
• Mixer kinetic (physical) temperature(tkxc)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Dummy altitude for Zeb(alt)
• lat(lat)
• Actual elevation angle(actel)
• Actual Azimuth(actaz)

• Raw data stream - documentation not supported(Raw data stream - documentation not supported)

TWP/MWR/C2 - Missing data

The heater blower assembly was causing the fuse to blow.  The instrument was taken offline 
until a replacement arrives.

• 31.4 GHz sky signal(sky31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Mixer kinetic (physical) temperature(tkxc)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Blackbody kinetic temperature(tkbb)
• lat(lat)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• 31.4 GHz blackbody(bb31)
• MWR column precipitable water vapor(vap)
• 23.8 GHz sky signal(sky23)
• Ambient temperature(tkair)
• IR Brightness Temperature(ir_temp)
• base time(base_time)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• lon(lon)
• 23.8 GHz Blackbody signal(bb23)
• (tknd)
• Actual Azimuth(actaz)
• Time offset of tweaks from base_time(time_offset)
• Actual elevation angle(actel)
• Dummy altitude for Zeb(alt)
• Sky Infra-Red Temperature(sky_ir_temp)
• Temperature correction coefficient at 31.4 GHz(tc31)

• Raw data stream - documentation not supported(Raw data stream - documentation not supported)

• lat(lat)
• Standard deviation about the mean for the total water vapor amount(vap_sdev)
• lon(lon)
• Fraction of data in averaging interval with water on Teflon window(water_flag_fraction)
• Averaged total liquid water along LOS path(liq)
• Standard deviation about the mean for the 31.4 GHz sky brightness temperature(tbsky31_sdev)
• IR Brightness Temperature(ir_temp)
• Time offset of tweaks from base_time(time_offset)
• Number of data points averaged for 23tbsky, 31tbsky, vap & liq(num_obs)
• Standard deviation about the mean for the 23.8 GHz sky brightness temperature(tbsky23_sdev)
• Dummy altitude for Zeb(alt)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Number of points included in the ir_temp ensemble(num_obs_irt)
• base time(base_time)
• Standard deviation about the mean for the IR brightness temperature(ir_temp_sdev)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• MWR column precipitable water vapor(vap)
• Standard deviation about the mean for the total liquid water amount(liq_sdev)

• 31.4 GHz sky signal(tipsky31)
• lat(lat)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.4 GHz goodness-of-fit coefficient(r31)
• Actual Azimuth(actaz)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 31.4 GHz blackbody(bb31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Ambient temperature(tkair)
• Dummy altitude for Zeb(alt)
• (tknd)
• base time(base_time)
• Blackbody kinetic temperature(tkbb)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Time offset of tweaks from base_time(time_offset)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Actual elevation angle(actel)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• 23.8 GHz Blackbody signal(bb23)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• lon(lon)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Mixer kinetic (physical) temperature(tkxc)

TWP/MWR/C1 - Radiometer failure

The instrument stopped responding and had to be powered off. Suspect cause of failure is a 
faulty digital board.

• Raw data stream - documentation not supported(Raw data stream - documentation not supported)

• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 23.8 GHz(tc23)
• IR Brightness Temperature(ir_temp)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Actual Azimuth(actaz)
• 23.8 GHz Blackbody signal(bb23)
• Blackbody kinetic temperature(tkbb)
• lat(lat)
• 31.4 GHz blackbody(bb31)
• (tknd)
• 31.4 GHz sky signal(sky31)
• base time(base_time)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Dummy altitude for Zeb(alt)
• Actual elevation angle(actel)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• MWR column precipitable water vapor(vap)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Ambient temperature(tkair)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Time offset of tweaks from base_time(time_offset)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Sky Infra-Red Temperature(sky_ir_temp)
• 23.8 GHz sky signal(sky23)
• lon(lon)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)

• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 31.4 GHz goodness-of-fit coefficient(31r)
• 31.4 GHz blackbody(31bb)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• lat(lat)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• 23.8 GHz noise diode calib (injection temp) at Tkxc(23ndiode)
• Actual elevation angle(actel)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Tip configuration number(tipn)
• 23.8 GHz Blackbody signal(23bb)
• Mixer kinetic (physical) temperature(tkxc)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• 31.4 GHz blackbody signal(31tipbb)
• base time(base_time)
• IR Brightness Temperature(ir_temp)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 23.8 GHz calibration curve slope(23gain)
• Airmass value(airm)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz Blackbody signal(bb23)
• 23.8 GHz blackbody signal(23tipbb)
• Ambient temperature(tkair)
• Time offset of tweaks from base_time(time_offset)
• 31.4 GHz noise diode calib adjusted to tknd_nom and low_pass filltered(31expave)
• lon(lon)
• (tknd)
• 23.8 GHz blackbody+noise injection signal(23bbn)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 23.8 GHz calibration curve offset(23tbzenith)
• Blackbody kinetic temperature(tkbb)
• 31.4 GHz sky signal+noise injection signal(31tipskynd)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• 31.4 GHz calibration curve offset(31tbzenith)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 31.4 GHz sky signal(31tipsky)
• 23.8 GHz sky signal(23tipsky)
• 23.8 GHz sky signal(tipsky23)
• Dummy altitude for Zeb(alt)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz goodness-of-fit coefficient(23r)
• 31.4 GHz noise diode calib (injection temp) at Tkxc(31ndiode)
• 31.4 GHz blackbody+noise injection signal(31bbn)
• 31.4 GHz calibration curve slope(31gain)
• 31.4 GHz blackbody(bb31)
• Blackbody temperature 1(tkbb1)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 23.8 GHz noise diode calib adjusted to tknd_nom and low_pass filltered(23expave)
• Blackbody temperature 2(tkbb2)
• Temperature correction coefficient at 31.4 GHz(tc31)
• 23.8 GHz sky signal+noise injection signal(23tipskynd)
• Actual Azimuth(actaz)

TWP/MWR/C3 - Sun in field of view of radiometer

Each day from 9/20 and 10/9 around local noon, there is an increase in the brightness 
temperature due to the sun being in the field of view of the radiometer.

• MWR column precipitable water vapor(vap)
• Averaged total liquid water along LOS path(liq)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)

• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• 23.8 GHz sky signal(tipsky23)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)

TWP/MWR/C2 - Missing Data

Data are missing and unrecoverable.

• 31.4 GHz sky signal(sky31)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Mixer kinetic (physical) temperature(tkxc)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Blackbody kinetic temperature(tkbb)
• lat(lat)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• lon(lon)
• 23.8 GHz Blackbody signal(bb23)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• 31.4 GHz blackbody(bb31)
• MWR column precipitable water vapor(vap)
• 23.8 GHz sky signal(sky23)
• (tknd)
• Actual Azimuth(actaz)
• Ambient temperature(tkair)
• IR Brightness Temperature(ir_temp)
• Time offset of tweaks from base_time(time_offset)
• Actual elevation angle(actel)
• base time(base_time)
• Dummy altitude for Zeb(alt)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Sky Infra-Red Temperature(sky_ir_temp)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)

TWP/MWR/C2 - Reprocessed: New Calibration coefficients

On 11/27 a spare radiometer was installed to replace a faulty radiometer. Once the 
radiometer started to collect data it used the default calibration coefficients until it 
collected enough tip data to determine its own coefficients.

The data were reprocessed to apply corrected calibrations and the reprocessed data were 
archived 20061222.

• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• MWR column precipitable water vapor(vap)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)

• Temperature correction coefficient at 23.8 GHz(tc23)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Temperature correction coefficient at 31.4 GHz(tc31)

TWP/MWR/C1 - Missing data

Data are missing and unrecoverable.

• (tknd)
• 31.4 GHz blackbody(bb31)
• Mixer kinetic (physical) temperature(tkxc)
• 31.4 GHz sky signal(sky31)
• base time(base_time)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Dummy altitude for Zeb(alt)
• Actual elevation angle(actel)
• Temperature correction coefficient at 23.8 GHz(tc23)
• Temperature correction coefficient at 31.4 GHz(tc31)
• IR Brightness Temperature(ir_temp)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• MWR column precipitable water vapor(vap)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Ambient temperature(tkair)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Time offset of tweaks from base_time(time_offset)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Sky Infra-Red Temperature(sky_ir_temp)
• Actual Azimuth(actaz)
• 23.8 GHz Blackbody signal(bb23)
• 23.8 GHz sky signal(sky23)
• lon(lon)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• Blackbody kinetic temperature(tkbb)
• lat(lat)

TWP/MWR/C1/C2 - Sun in the field of view

Every day between 3/7 and 4/2 around noon local time there is an increase in the 
brightness temperatures due to the sun in the field of vie of the radiometer.

• 31.4 GHz sky signal(sky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• MWR column precipitable water vapor(vap)
• 23.8 GHz sky signal(sky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)

• MWR column precipitable water vapor(vap)
• 31.4 GHz sky signal(sky31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Averaged total liquid water along LOS path(liq)
• 23.8 GHz sky signal(sky23)

• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)

• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz sky signal(tipsky23)

TWP/MWR/C1 - Intermittent data

After a computer change the MWR program did not restart properly.  Data are intermittent 
between 6/12 and 6/17.

• Mixer kinetic (physical) temperature(tkxc)
• Temperature correction coefficient at 23.8 GHz(tc23)
• IR Brightness Temperature(ir_temp)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• Sky brightness temperature at 23.8 GHz(tbsky23)
• Actual Azimuth(actaz)
• 23.8 GHz Blackbody signal(bb23)
• Blackbody kinetic temperature(tkbb)
• lat(lat)
• 31.4 GHz blackbody(bb31)
• (tknd)
• 31.4 GHz sky signal(sky31)
• base time(base_time)
• Sky brightness temperature at 31.4 GHz(tbsky31)
• Dummy altitude for Zeb(alt)
• Actual elevation angle(actel)
• Temperature correction coefficient at 31.4 GHz(tc31)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• MWR column precipitable water vapor(vap)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• Ambient temperature(tkair)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Time offset of tweaks from base_time(time_offset)
• Averaged total liquid water along LOS path(liq)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• Sky Infra-Red Temperature(sky_ir_temp)
• 23.8 GHz sky signal(sky23)
• lon(lon)
• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)

• Noise injection temp at 31.4 GHz adjusted to tkbb(tnd31)
• 31.4 GHz goodness-of-fit coefficient(31r)
• 31.4 GHz blackbody(31bb)
• Noise injection temp at nominal temperature at 23.8 GHz(tnd_nom23)
• lat(lat)
• 23.8 GHz goodness-of-fit coefficient(r23)
• Noise injection temp at 31.4 GHz derived from this tip(tnd31I)
• 31.8 GHz sky brightness temperature derived from tip curve(tbskytip31)
• 23.8 GHz noise diode calib (injection temp) at Tkxc(23ndiode)
• Actual elevation angle(actel)
• Total liquid water along zenith path using tip-derived brightness temperatures(liqtip)
• Tip configuration number(tipn)
• 23.8 GHz Blackbody signal(23bb)
• Mixer kinetic (physical) temperature(tkxc)
• Water on Teflon window (1=WET, 0=DRY)(wet_window)
• 31.4 GHz blackbody signal(31tipbb)
• base time(base_time)
• IR Brightness Temperature(ir_temp)
• Total water vapor along zenith path using tip-derived brightness temperatures(vaptip)
• 31.4 GHz blac2body+noise injection signal(bbn31)
• 23.8 GHz calibration curve slope(23gain)
• Airmass value(airm)
• 31.4 GHz sky signal(tipsky31)
• 23.8 GHz Blackbody signal(bb23)
• 23.8 GHz blackbody signal(23tipbb)
• Ambient temperature(tkair)
• Time offset of tweaks from base_time(time_offset)
• 31.4 GHz noise diode calib adjusted to tknd_nom and low_pass filltered(31expave)
• lon(lon)
• (tknd)
• 23.8 GHz blackbody+noise injection signal(23bbn)
• 31.4 GHz goodness-of-fit coefficient(r31)
• 23.8 GHz calibration curve offset(23tbzenith)
• Blackbody kinetic temperature(tkbb)
• 31.4 GHz sky signal+noise injection signal(31tipskynd)
• 23.8 GHz blackbody+noise injection signal(bbn23)
• 23.8 GHz sky brightness temperature derived from tip curve(tbskytip23)
• 31.4 GHz calibration curve offset(31tbzenith)
• Noise injection temp at 23.8 GHz adjusted to tkbb(tnd23)
• 31.4 GHz sky signal(31tipsky)
• 23.8 GHz sky signal(23tipsky)
• 23.8 GHz sky signal(tipsky23)
• Dummy altitude for Zeb(alt)
• Noise injection temp at nominal temperature at 31.4 GHz(tnd_nom31)
• Temperature correction coefficient at 23.8 GHz(tc23)
• 23.8 GHz goodness-of-fit coefficient(23r)
• 31.4 GHz noise diode calib (injection temp) at Tkxc(31ndiode)
• 31.4 GHz blackbody+noise injection signal(31bbn)
• 31.4 GHz calibration curve slope(31gain)
• 31.4 GHz blackbody(bb31)
• Blackbody temperature 1(tkbb1)
• Noise injection temp at 23.8 GHz derived from this tip(tnd23I)
• 23.8 GHz noise diode calib adjusted to tknd_nom and low_pass filltered(23expave)
• Blackbody temperature 2(tkbb2)
• Temperature correction coefficient at 31.4 GHz(tc31)
• 23.8 GHz sky signal+noise injection signal(23tipskynd)
• Actual Azimuth(actaz)

TWP/MWR/C1 - Incorrect ambient temperature readings

Starting on 11/21 the ambient temperature readings are intermittent and have spikes.
Site operators replaced the dew-blower on 12/11 and readings came back to normal

• Ambient temperature(tkair)

• Ambient temperature(tkair)